Pioneer DVL-K88, Руководство по обслуживанию

Страница: 107 / 134

20
DV-505, DVL-909, DV-S9
3.8.3 Startup Sequence
The basic flow is shown below. The parentheses indicate a limitation:
“base” represents base models, such as the DV-505 and DV-S9,
and “compatibles” represents DVD-LD compatible models, such as
the DVL-909.
(1) Closes the tray.
(2) Runs the tilt servo for 1.5 seconds (compatibles).
(3) Detects the peak.
(4) Distinguishes the disc.
(5) SGC
(6) Turns on the focus servo.
(7) Turns on the tilt servo (compatibles).
(8) Starts the spindle rotation.
(9) ATB
(10) Measures the MIRR modulation degree.
(11) Turns on the tracking servo.
(12) Turns on the slider servo.
(13) Turns on the spindle servo.
(14) Focus AGC
(15) Tracking AGC
(16) AFB
(17) Plays AGC (base for CDs)
(18) Plays back.
∗
For a 2-layer DVD, steps (9) through (16) are repeated for each
layer.
∗
When starting up with [TV/LDP] in Test mode, all the steps (1)
to (18) are performed for a DVD, and steps (1) to (10) are
performed for a CD.
3.8.4 Peak Detection
Overview
This is a new function to measure the size and location of the sine
wave related to focus errors at the beginning. The measurement is
performed in the normal startup process and in Test mode, as well.
If the sine wave is small, the OE IC gain is switched. Only the
judgment for NO DISC is accomplished at this time. The operation
is in effect as for judgment for DISC .
Using the Function in Test Mode
This function is not assigned to any remote control keys. Only an
open/close operation can trigger the function.
3.8.5 Disc Distinction
Overview
This function is almost the same as that with the first-generation
models. The only difference is as follows: If an error occurs in the
startup sequence and playback cannot be started, startup is retried
after forcibly switching the disc distinction from DVD to CD or
vice verse by a backup process. If startup fails again, it is canceled,
and an error is generated. The types of error that triggers the backup
process for disc distinction are discussed in the next section.
Using the Function in Test Mode
This function is not assigned to any remote control keys. Only an
open/close operation can trigger the function.
3.8.6 SGC
Overview
This is a new function to maintain the sine wave related to focus
errors to a certain size so that the sine wave shows 1.8 V for the P-
to-P value.
This operation is performed each time after judging disc presence
and distinction in the normal startup process and in Test mode, as
well. The operation is achieved by switching the FE gain inside the
RF IC (LA9700) by using the voltage at the SGC connector (pin 22)
of the RF IC.
Using the Function in Test Mode
This function is not assigned to any remote control keys. Only an
open/close operation can trigger the function.
3.8.7 Measurement of MIRR Modulation
Degree
Overview
The slice voltage of the RF signal is measured and used in the
calculation to generate the MIRR signal. This operation is made in
synchronization with ATB ON/OFF in normal startup and in Test
mode, as well.
3.8.8 AFB (Auto Focus Bias) Function
Overview
Among the first-generation models, this function supports only CDs
with the basic models, such as the DV-7. Among the new models,
this function supports DVDs with all models, but CDs only with the
basic models. The operation is executed only once (once for each
layer for a 2-layer DVD) after the focus and tracking AGC at startup.
The operation is accomplished not by centering the focus servo to
Vref (2.5 V), but by gradually changing the center value for the
optimum jitter value. Thus, performance with an improper or dirty
disc (by fingerprints, etc.), or the temperature characteristics (at 0
°
C,
35
°
C, etc.) will be improved.
OverviewUsing the Function in Test mode
(the Remote Control Keys to be Used are
Indicated in Brackets)
As the function is to be synchronized with AGC, turn on and off
AFB by pressing [TEST] + [7]. The jitter value measurement cannot
be made with AFB ON.