3
Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
FAD/BAL
(fader/balance adjustment)
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between fader (front/rear) and
balance (left/right).
3
Turn
M.C.
to adjust speaker balance.
PRESET EQ
(equalizer recall)
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the equalizer.
DYNAMIC
—
VOCAL
—
NATURAL
—
CUSTOM
—
FLAT
—
POWERFUL
!
You can also switch the equalizer by pressing
repeatedly.
TONE CTRL
(equalizer adjustment)
!
Adjusted equalizer curve settings are stored in
CUSTOM
.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to select
BASS
(bass)/
MID
(mid)/
TRE-
BLE
(treble).
3
Turn
M.C.
to adjust the level.
Adjustment range:
+6
to
-6
LOUD
(loudness)
Loudness compensates for deficiencies in the low-fre-
quency and high-frequency ranges at low volume.
1
Press
M.C.
to select the desired setting.
OFF
(off)
—
LOW
(low)
—
HI
(high)
SUB.W
(subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press
M.C.
to select the desired setting.
NOR
(normal phase)
—
REV
(reverse phase)
—
OFF
(subwoofer off)
SUB.W CTRL
(subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
!
When you select
OFF
in
SUB.W
, you cannot select
this function. For details, refer to
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between the cut-off frequency
and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)
—
Output level (Output level display
flashes.)
3
Turn
M.C.
to select the desired setting.
Cut-off frequency:
50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
Output level:
–
24
to
+6
SLA
(source level adjustment)
SLA
(Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
Settings are based on the FM volume level, which
remains unchanged.
!
When selecting FM as the source, you cannot
switch to
SLA
.
!
The MW/LW volume level can also be adjusted
with this function.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range:
+4
to
–
4
En
22
Section
02
Operating this unit
130.com.ua
Autogood products «130»
Содержание DVH-340UB
Страница 2: ...Operation Manual DVD RDS RECEIVER DVH 340UB English 1 3 0 c o m u a Autogood products 130 ...
Страница 42: ...En 41 1 3 0 c o m u a Autogood products 130 ...
Страница 43: ...En 42 1 3 0 c o m u a Autogood products 130 ...
Страница 44: ...En 43 1 3 0 c o m u a Autogood products 130 ...
