background image

DV-366-S

86

1

2

3

4

1

2

3

4

C

D

F

A

B

E

7.3  DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY

Disc / content format 
playback compatibility

General disc compatibility

This player was designed and engineered to 
be compatible with software bearing one or 
more of the following logos:

• KODAK Picture CD

 is a trademark of Fuji Photo Film Co. 

Ltd.

This player supports the IEC’s Super VCD 
standard. Compared to the Video CD stan-
dard, Super VCD offers superior picture 
quality, and allows two stereo soundtracks to 
be recorded. Super VCD also supports the 
widescreen size.

Other formats, including but not limited to the 
following, are not playable in this player:

DVD-Audio / SACD / DVD-RAM
DVD-ROM / CD-ROM

*

* Except those that contain MP3, WMA or 

JPEG. See also Compressed audio compat-
ibility and JPEG file compatibility below.

DVD-R/RW and CD-R/RW discs (Audio CDs 
and Video CD/Super VCDs) recorded using a 
DVD recorder, CD recorder or personal 
computer may not be playable on this unit. 
This may be caused by a number of possibili-
ties, including but not limited to: the type of 
disc used; the type of recording; damage, dirt 
or condensation on either the disc or the 
player’s pick-up lens. See below for notes 
about particular software and formats.

CD-R/RW compatibility

• This unit will play CD-R and CD-RW discs 

recorded in CD Audio or Video CD/Super 
VCD format, or as a CD-ROM containing 
MP3, WMA or JPEG files. However, any 
other content may cause the disc not to 
play, or create noise/distortion in the 
output.

• This unit cannot record CD-R or CD-RW 

discs.

• Unfinalized CD-R/RW discs recorded as 

CD Audio can be played, but the full Table 
of Contents (playing time, etc.) will not be 
displayed.

DVD-R/RW compatibility

• This unit will play DVD-R/RW discs 

recorded using the DVD-Video format that 
have been finalized using a DVD-recorder.

• This unit will play DVD-RW discs recorded 

using the Video Recording (VR) format.

DVD-RW

 shows in the display when a VR 

format DVD-RW disc is loading.

DVD-Video

DVD-R

DVD-RW

Video CD

Fujicolor CD

Audio CD

CD-R

CD-RW

VIDEO

CD

Super Video CD (Super VCD)

Содержание DV-366-S































































































Отзывы: