Pioneer DEH-X7590SD, Руководство пользователя

Страница: 14 / 24

S/W control (rear output and subwoofer setting)
This unit
’
s rear output (rear speaker leads output
and RCA rear output) can be used for full-range
speaker (
Rear SP :F.Range ) or subwoofer ( Rear
SP :S/W ) connection. If you switch the rear output
setting to
Rear SP :S/W
, you can connect a rear
speaker lead directly to a subwoofer without using
an auxiliary amp.
1
Press M.C. to switch the rear output setting.
!
When no subwoofer is connected to the
rear output, select
Rear SP :F.Range (full-
range speaker).
!
When a subwoofer is connected to the rear
output, select
Rear SP :S/W
(subwoofer).
!
Even if you change this setting, there will be
no output unless you turn the subwoofer out-
put on (refer to
Subwoofer1 (subwoofer on/off
setting) on page 10).
!
If you change this setting, subwoofer output in
the audio menu will return to the factory set-
tings.
!
Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this set-
ting.
System menu
1 Press and hold SRC/OFF until the unit
turns off.
2 Press and hold M.C. until the main menu
appears in the display.
3 Turn M.C. to change the menu option
and press to select SYSTEM.
4 Turn M.C. to select the system menu
function.
For details, refer to System menu on the pre-
vious page.
Using an AUX source
1 Insert the stereo mini plug into the AUX
input jack.
2 Press SRC/OFF to select AUX as the
source.
Note
AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to
AUX
(auxiliary input) on the previous page.
Turning the display off or on
%
Press and hold MIX/DISP OFF until the
display turns on or off.
If an unwanted display appears
Turn off the unwanted display using the proce-
dures listed below.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to display DEMO OFF and press
to select.
4 Turn M.C. to switch to YES.
5 Press M.C. to select.
Connections
WARNING
!
Use speakers over 50 W (output value) and
between 4
W
to 8
W
(impedance value). Do
not use 1
W
to 3
W
speakers for this unit.
!
The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly con-
nected to metal parts of the car
’
s body. The
ground wire of the power amp and the one of
this unit or any other device must be con-
nected to the car separately with different
screws. If the screw for the ground wire loos-
ens or falls out, it could result in fire, genera-
tion of smoke or malfunction.
Ground wire
Metal parts of car’s body
POWER AMP
Other devices
(Another electronic
device in the car)
Important
!
When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
ON
S
T
A
R
T
O
FF
ACC position No ACC position
!
Use this unit with a 12-volt battery and nega-
tive grounding only. Failure to do so may re-
sult in a fire or malfunction.
!
To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
—
Disconnect the negative terminal of the bat-
tery before installation.
—
Secure the wiring with cable clamps or adhe-
sive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
—
Place all cables away from moving parts,
such as the shift lever and seat rails.
—
Place all cables away from hot places, such
as near the heater outlet.
—
Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
—
Cover any disconnected cable connectors
with insulating tape.
—
Do not shorten any cables.
—
Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
—
Use a fuse of the rating prescribed.
—
Never wire the negative speaker cable directly
to ground.
—
Never band together negative cables of multi-
ple speakers.
!
When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an ex-
ternal power amp or the vehicle
’
s auto-anten-
na relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
!
Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
Using this unit
14
Section
Installation
En
02
03