Pioneer DEH-X7500SD, Руководство по установке

Страница: 3 / 32

Important
!
When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
ON
S
T
A
R
T
O
FF
ACC position No ACC position
!
Use of this unit in conditions other than the
following could result in fire or malfunction.
—
Vehicles with a 12-volt battery and negative
grounding.
—
Speakers with 50 W (output value) and 4
W
to
8
W
(impedance value).
!
To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
—
Disconnect the negative terminal of the bat-
tery before installation.
—
Secure the wiring with cable clamps or adhe-
sive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
—
Place all cables away from moving parts,
such as the shift lever and seat rails.
—
Place all cables away from hot places, such
as near the heater outlet.
—
Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
—
Cover any disconnected cable connectors
with insulating tape.
—
Do not shorten any cables.
—
Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
—
Use a fuse of the rating prescribed.
—
Never wire the negative speaker cable directly
to ground.
—
Never band together negative cables of multi-
ple speakers.
!
When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an ex-
ternal power amp or the vehicle
’
s auto-anten-
na relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
!
Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
!
The black cable is ground. Ground cables for
this unit and other equipment (especially,
high-current products such as power amps)
must be wired separately. If they are not, an
accidental detachment may result in a fire or
malfunction.
This unit
3 5 6 a 7 b
c
8
1
2
9
d
4
1
USB port 1
2
USB port 2 (DEH-X8500DAB and DEH-
X8500BT only)
3 Antenna input
15 cm
4
DAB antenna input (DEH-X8500DAB only)
To receive DAB signals, connect a DAB an-
tenna (AN-DAB1) sold separately to the unit.
5
Fuse (10 A)
6
Power cord input
7 Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
8
Microphone input (DEH-X8500DAB and
DEH-X8500BT only)
9 Microphone (DEH-X8500DAB and DEH-
X8500BT only)
4 m
a
Rear output
b
Front output
c Subwoofer output
d
USB cable
1.5 m
!
Only for DEH-X8500DAB and DEH-X8500BT
If connecting both USB1 (USB storage
device1)/ iPod1 (iPod connected using
USB input1) and
USB2
(USB storage de-
vice2)/ iPod2 (iPod connected using USB
input2) at the same time, use a Pioneer
USB cable (CD-U50E) in addition to the
regular Pioneer USB cable.
Power cord
1
3
3
2
4
4
5
5
6
6
b
8
9
a
7
c
e
d
1
To power cord input
2 Depending on the kind of vehicle, the func-
tion of
3
and
5
may be different. In this
case, be sure to connect
4
to
5
and
6
to
3
.
3
Yellow
Back-up (or accessory)
4
Yellow
Connect to the constant 12 V supply termi-
nal.
5
Red
Accessory (or back-up)
6
Red
Connect to terminal controlled by ignition
switch (12 V DC).
7
Connect leads of the same color to each
other.
8
Orange/white
Connect to lighting switch terminal.
9
Black (chassis ground)
English
Connections
3
Section
Connections
En
02