Pioneer DEH-5400BT, Руководство пользователя

Страница: 11 / 72

FAD/BAL (fader/balance adjustment)
1
Press M.C. to display the setting mode.
2
Press
M.C.
to cycle between fader (front/rear)
and balance (left/right).
3
Turn M.C. to adjust speaker balance.
!
When the rear output and RCA output setting
are
SW , you cannot adjust front/rear speaker
balance. Refer to
REAR-SP
(rear output setting)
on this page. Refer to PREOUT (preout setting)
on this page.
PRESET EQ (equalizer recall)
1
Press M.C. to display the setting mode.
2
Turn M.C. to select the equalizer.
DYNAMIC
—
VOCAL
—
NATURAL
—
CUSTOM
—
FLAT
—
POWERFUL
3
Press M.C. to confirm the selection.
TONE CTRL (equalizer adjustment)
!
Adjusted equalizer curve settings are stored in
CUSTOM .
1
Press M.C. to display the setting mode.
2
Press
M.C.
to select
BASS
(bass)/
MID
(mid)/
TREBLE (treble).
3
Turn M.C. to adjust the level.
Adjustment range: +6 to
–
6
LOUD (loudness)
Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1
Press M.C. to select the desired setting.
OFF
(off)
—
LOW
(low)
—
HI
(high)
SUB.W (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press
M.C.
to select the desired setting.
NOR (normal phase)
—
REV (reverse phase)
—
OFF (subwoofer off)
SUB.W CTRL (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
!
When you select OFF in SUB.W , you cannot se-
lect this function. For details, refer to SUB.W
(subwoofer on/off setting) on this page.
1
Press
M.C.
to display the setting mode.
2
Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)
—
Output level (Output level display
flashes.)
3
Turn
M.C.
to select the desired setting.
Cut-off frequency: 50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
Output level:
–
24 to +6
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
!
Settings are based on the FM volume level,
which remains unchanged.
!
The AM volume level can also be adjusted with
this function.
!
When selecting FM as the source, you cannot
switch to
SLA .
1
Press M.C. to display the setting mode.
2
Turn M.C. to adjust the source volume.
Adjustment range: +4 to
–
4
3
Press
M.C.
to confirm the selection.
Initial settings
1 Press and hold SRC/OFF until the unit
turns off.
2 Press M.C. and hold until function name
appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET
(setting the clock)
1
Press M.C. to display the setting mode.
2
Press M.C. to select the segment of the clock
display you wish to set.
Hour
—
Minute
3
Turn
M.C.
to adjust the clock.
AUX (auxiliary input)
Activate this setting when using an auxiliary de-
vice connected to this unit.
1
Press
M.C.
to turn
AUX
on or off.
USB PNP (plug and play)
This setting allows you to switch your source to
USB / iPod automatically.
1
Press
M.C.
to turn the plug and play function
on or off.
ON
–
When a USB storage device/iPod is con-
nected, depending on the type of device, the
source is automatically switched to
USB / iPod
when you turn on the engine. If you disconnect
your USB storage device/iPod, this unit
’
s
source is turned off.
OFF
–
When a USB storage device/iPod is con-
nected, the source is not switched to USB /
iPod
automatically. Please change the source
to USB / iPod manually.
REAR-SP
(rear output setting)
The rear speaker leads output can be used for full-
range speaker or subwoofer connection.
If you switch to
SW , you can connect a rear speak-
er lead directly to a subwoofer without using an
auxiliary amp.
Initially,
REAR-SP is set for rear full-range speaker
connection ( FUL ).
1
Press
M.C.
to select the desired setting.
FUL
—
SW
!
Even if you change this setting, there will
be no output if you select
OFF in SUB.W
(Refer to SUB.W (subwoofer on/off setting)
on this page).
!
If you change this setting, subwoofer out-
put in the audio menu will return to the fac-
tory settings.
PREOUT (preout setting)
The RCA outputs can be used for rear speaker or
subwoofer connection.
If you switch to
SW , you can connect a rear speak-
er lead directly to a subwoofer without using an
auxiliary amp.
Initially,
PREOUT
is set for rear full-range speaker
connection ( SW ).
1
Press M.C. to select the desired setting.
SW
—
REA
!
Even if you change this setting, there will
be no output if you select
OFF
in
SUB.W
(Refer to SUB.W (subwoofer on/off setting)
on this page).
!
If you change this setting, subwoofer out-
put in the audio menu will return to the fac-
tory settings.
DEMO
(demo display setting)
1
Press M.C. to turn the demo display on or off.
SCROLL
(scroll mode setting)
English
Operating this unit
11
Section
Operating this unit
En
02