09
58
En
Chapter 9
Additional information
Serial interface
specifications
In addition to the basic o
p
e
r
ations on the
p
laye
r
's f
r
ont
p
anel and
r
emote cont
r
ol, the
p
laye
r
is equi
pp
ed with a
se
r
ial inte
r
face confo
r
ming to RS-232C standa
r
ds allowing
connection to a com
p
ute
r
. The inte
r
face is a 9-
p
in D-Sub
connecto
r
.
Caution
• The 9-
p
in connecto
r
uses inch sc
r
ew th
r
eads.
The D-Sub connecto
r
's
p
in layout is as shown below.
Serial control specifications
(1) Signal level
RS-232C level
(2) Data format
Data length: 8 bits
Sto
p
bit: 1 bit
Pa
r
ity: None
(3) Communication speed (Baud rate)
The communication s
p
eed (Baud
r
ate) is selectable
among the following:
2400 bps
,
4800 bps
,
9600 bps
,
19200 bps
and
115200 bps
. Set to
9600 bps
by
facto
r
y default (
p
age 56).
Connection to a computer
The
p
laye
r
communicates with the com
p
ute
r
using the
9-
p
in D-Sub connecto
r
's
p
ins 2 and 3 fo
r
signal t
r
ansfe
r
and
p
in 5 as the g
r
ound.
The com
p
ute
r
and
p
laye
r
a
r
e connected as shown on the
diag
r
am below.
The
p
laye
r
can acce
p
t commands wheneve
r
the
p
owe
r
is
on. In addition, the
p
laye
r
can acce
p
t the commands
below even when the
p
owe
r
is off.
• Powe
r
ON command
• Play command
• Commands with the
p
owe
r
(A181AFBC),
p
lay
(A181AF39) and
p
owe
r
on (A181AFBA) Remote
Cont
r
ol Button commands as a
r
guments.
The
r
e is no need to connect cont
r
ol lines othe
r
than
TxD
and
RxD
.
Pin no. Terminal
Input/Output
Function
1
DCD
In
p
ut
NC (not connected on
the
p
laye
r
)
2
RxD
In
p
ut
r
eceive data
3
TxD
Out
p
ut
send data
4
DTR
Out
p
ut
NC (not connected on
the
p
laye
r
)
5
GND
--
g
r
ound
6
DSR
In
p
ut
NC (not connected on
the
p
laye
r
)
7
RTS
Outu
p
t
Connected to CTS
p
in
inte
r
nally.
8
CTS
In
p
ut
Connected to RTS
p
in
inte
r
nally.
9
RI
In
p
ut
NC (not connected on
the
p
laye
r
)
5
1
6
9
RxD
TxD
GND
BDP-V6000
RxD
Pin 2
Pin 3
Pin 5
Pin 2
Pin 3
Pin 5
TxD
GND
Control terminal such as
a computer
V6000_CUXJ_EN.book 58 ページ 2009年6月5日 金曜日 午前11時57分