Pioneer AVIC-5201NEX, Руководство по установке

Страница: 4 / 32

4
En
<CRD5002-A> UC
Connection
Precautions before
connecting the system
WARNING
Do not take any steps to tamper with or
disable the parking brake interlock system
which is in place for your protection.
Tampering with or disabling the parking
brake interlock system could result in serious
injury or death.
CAUTION
•
If you decide to perform the installation
yourself, and have special training and
experience in the mobile electronics
installations, please carefully follow all of
the steps in the installation manual.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wiring
to remain exposed.
•
Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause the
insulation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. If the yellow
lead’s insulation tears as a result of contact
with metal parts, short-circuiting can occur,
resulting in considerable danger.
•
It is extremely dangerous to allow cables to
become wound around the steering column
or shift lever. Be sure to install this product,
its cables, and wiring away in such so that
they will not obstruct or hinder driving.
• Make sure that the cables and wires will not
interfere with or become caught in any of
the vehicle’s moving parts, especially the
steering wheel, shift lever, parking brake,
sliding seat tracks, doors, or any of the
vehicle’s controls.
• Do not route wires where they will be
exposed to high temperatures. If the
insulation heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to the
product.
• Do not cut the GPS antenna cable to
shorten it or use an extension to make it
longer. Altering the antenna cable could
result in a short circuit or malfunction.
• Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse resistor
or filter, etc.) may fail to work properly.
• Never feed power to other electronic
products by cutting the insulation of the
power supply lead of this product and
tapping into the lead. The current capacity
of the lead will be exceeded, causing
overheating.
Before installing this
product
• Use this product with a 12-volt
battery and negative grounding only.
Failure to do so may result in a fire or
malfunction.
• To avoid shorts in the electrical system,
be sure to disconnect the (–) battery
cable before installation.
To prevent damage
WARNING
• Use speakers over 50 W (maximum input
power) and between 4Ω to 8Ω (impedance
value). Do not use 1Ω to 3Ω speakers for
this product.
• The black cable is ground. When
installing this product or power amp (sold
separately), make sure to connect the
ground wire first. Ensure that the ground
wire is properly connected to metal parts
of the car’s body. The ground wire of the
power amp and the one of this product or
any other device must be connected to the
car separately with different screws. If the
screw for the ground wire loosens or falls
out, it could result in fire generation of
smoke or malfunction.
Ground wire
Metal parts of car’s body
*1
Not supplied for this unit.
Power amp
Other devices
(Another electronic
device in the car)
• When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
– When disconnecting a connector, pull the
connector itself. Do not pull the lead, as you
may pull it out of the connector.
– This product cannot be installed in a vehicle
without ACC (accessory) position on the
ignition switch.
ACC position No ACC position
• To avoid short-circuiting, cover the
disconnected lead with insulating tape. It is
especially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.
• Attach the connectors of the same color to
the corresponding colored port, i.e., blue
connector to the blue port, black to black, etc.
• Refer to the owner’s manual for details on
connecting the power amp and other units,
then make connections accordingly.
• Since a unique BPTL circuit is employed, do
not directly earth the side of the speaker
lead or connect the side of another side of
the speaker lead together. Be sure to connect
the side of the speaker lead to the side of
the speaker lead on this product.
Notice for the blue/white lead
Important
When this product is in “ Power OFF ” mode, the
control signal is also turned off. If “ Power OFF ”
mode is cancelled, the control signal is output
again and the aerial is extended with the auto
antenna function (if the antenna is being used).
Be careful so that the extended antenna does
not come into contact with any obstacles.
• When the ignition switch is turned on (ACC
ON), a control signal is output through the
blue/white lead. Connect to an external power
amp’s system remote control terminal, the
auto-antenna relay control terminal, or the
antenna booster power control terminal (max.
300 mA 12 V DC). The control signal is output
through the blue/white lead, even if the audio
source is switched off.
• Be sure not to use this lead as the power
supply lead for the external power amps. Such
connection could cause excessive current
drain and malfunction.
• Be sure not to use this lead as the power
supply lead for the auto-antenna or antenna
booster. Such connection could cause
excessive current drain and malfunction.