background image

12

Environmental information

EU directive 2002/95/EC on the Restriction of the use  
of certain hazardous substances in electrical and  
electronic equipment (RoHS)

It is Pike Signals Limited’s desire to meet customer requirements 
with respect to the RoHS initiative. We are actively working 
to achieve the important objective of making our products 
compliant with the EU RoHS directive (and similar initiatives) 
through efficient product design that reduces unnecessary 
waste; the use of recyclable materials throughout, and a transfer 
to lead-free components and solder. 

EU directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE)

Pike Signals Limited is focussed on developing 
a compliance program for the European 
Union (“EU”) Directive on Waste Electrical and 
Electronic Equipment, Directive 2002/96/EC. 
Under the EU WEEE Directive, manufacturers of 
covered electronic equipment are obligated to 
take back such products at the end of their useful 
life. 

Pike Signals Limited is committed to meeting or exceeding 
environmental standards in the production of all products and is 
engaged in a comprehensive, company-wide effort towards full 
compliance with the EU WEEE Directive. 

Warranty

RoboSign base units and the remote control are guaranteed 
against failure subject to fair wear and tear, correct operation 
and return to our works carriage paid. We undertake to repair or 
replace this equipment free of charge providing: 

•  It has been maintained in good condition and operated with 

due care, and

•  Any failures are directly traceable to faulty material or 

workmanship. 

However, we cannot entertain any claims for labour or other 
expenditure in connection therewith. Items or components 
subject to another manufacturer’s guarantee are subject to the 
terms of that guarantee only.
Any warranty given is void if seals on equipment are 
subsequently found to have been broken without prior permission 
by Pike Signals Limited.
Any item of equipment repaired by Pike Signals Limited is 
guaranteed from failure for three months from the date of repair, 
provided that the item has been subjected to fair usage and 
regular maintenance.

Disclaimers

Pike Signals Ltd reserves the right to change or alter product 
specifications without prior notice. The information contained 
within this guide is subject to copyright and may not reproduced 
in part or in full without prior written permission by Pike Signals 
Ltd. While every effort has been taken to ensure that this guide 
provides accurate information, no liability shall be accepted for 
any errors or omissions.
It is a policy of Pike Signals Ltd to seek registered design and/or 
patent protection for its products. 

www.ctxd.com

 

Documentation by:

Содержание RoboSign MK3

















Отзывы: