Pico Macom PRR-1 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

Pico Macom PRR-1 Скачать руководство пользователя страница 7

Fiber Optic

Series

CONTACT US

858.546.5050

www.

picomacom

.com

PICO MACOM

Fiber Optic

Series

The PRR receiver includes an autoranging power supply and may be installed in 120 or 240 VAC
systems by purchasing an appropriate power cord at the local PC computer shop if the supplied
cord is not appropriate.  (A NEMA-15P is supplied in North America.)  When powered, the front
panel POWER LED will be lighted and each receiver’s ONLINE LED will be lighted.  Operation is
simple, with only the RF ADJUST to be configured and, once set up for your application, the PRR
will continued to operate unattended.  The PRR will return to your set operating condition after
power outages and brown-outs.

This manual details the unit specifications, describes any issues that may be critical to your instal-
lation, discusses the operation, and, finally, outlines actions if you have problems with the unit.
If you read and follow the installation and operation chapters, the PRR should provide you years
of simple, reliable operation. In case of difficulty, the PRR is supported by the Standard Gold
Warranty program.

«
...
5
6
7
8
9
...
»

Содержание PRR-1

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды