ー3ー
ー6ー
PKI-0055
PKI-0055
Precautions for Use
● Keep the product out of reach of infants. Otherwise infants may swallow or break the product,
leading to injury.
● When the lamp is lit, the lens becomes hot. Do not wash the vehicle while the lights are on or
immediately after turning them off.
● When this bulb/lamp is tuned on, there is a possibility that noise interference may influence the
radio or other such devices. Please note that this is not a malfunction of any kind.
● During heavy rain or when putting the vehicle through a car wash, condensation may build up inside
the lamp due to the difference in temperature inside and outside the lamp. Please note that is will
not affect the overall function of the lamp.
● Do not leave the light illuminated while the vehicle is stopped for extended periods of time.
(Not to exceed 30 minutes or more).
● Before installing the LED bulb, make sure there is no visible damage or that there is any evidence of
it being dropped. If any part is broken or damaged, it may cause it to illuminate abnormally.
Precautions for Replacement
● When replacing the LED bulb, make sure the power is turned off and then remove the battery
minus (-) terminal before carrying out the replacement procedure. Not doing so may result in not
only a fire hazard but possible electrocution or bodily injury. In addition, please use rubber gloves
when carrying out this work process.
● As a result of replacing the bulb, the axis of the light may become misaligned. Therefore, after
replacement, check the lamp position and make necessary adjustments to the alignment.
● Make sure not to touch the base part or the area that illuminates light. Also, prevent any type of oil
or dirt from adhering to the product. If the light is turned on in this condition, it may cause a lighting
malfunction.
● Never turn the switch to "ON" when the LED bulb and the bulb connector are not connected.
● Make sure to prevent moisture from adhering to the product. If the light is turned on in this condition,
it may cause a lighting malfunction. If moisture is present, let it dry out thoroughly before use.
● Bulb replacement should be done safely on a flat surtace where a wide space is available.
Before replacement, stop the vehicle engine, apply the emergency brake, place the shift in parking
or neutral position, and pull out the key.
● Do not yank on the harness when disassembling. Doing so may damage the harness leading to
overheating and potential failure.
● Be careful not to lose the original bulbs by keeping them in a safe place after removal.
● Verify the position of the product as well as the metal base of the connector. Check the proper
direction and the install it securely.
● In the case of connector or terminal desorption, hold the connector terminal and straighten it out.
Please note that if excessive force is applied to the terminal it may break or it may no longer
connect. As a result it may cause damage leading to overheating and potential failure.
● Make sure not to apply excessive force to the light emitting part. If this part is damaged, it may
cause a lighting malfunction. Please handle this product with extreme care.
When installing to Multi-Reflector Type for HB3
Multi-Reflector
Type for HB3
Multi-Reflector
Type for HB3
Install the LED bulb to the lamp.
As shown in the illustration below, line up the
light-emitting part of the LED bulb (part ①) with
the high beam reflector so it faces sideways. Then
check to determine what direction and at what
angle it should be rotated and then remove the bulb.
Then adjust it using the procedures described in
Adjusting the position of the light-emitting section
on page 6
View of diagram directly from the front.
Install the LED bulb to the lamp.
As shown in the illustration below, line up the light-emitting part of the LED bulb (part ①) with the
fog lamp reflector so it faces sideways. Then check to determine what direction and at what angle
it should be rotated and then remove the bulb. Then adjust it using the procedures described in
Adjusting the position of the light-emitting section on page 6
When installing to fog lamp
LED bulb
LED bulb
Light-emitting part
Light-emitting part
View of diagram directly from the front.
Light-emitting part
Light-emitting part
Reflector for fog lamp