PI PIMag V-408 Скачать руководство пользователя

Страница: 22 / 44

Black arrows (aligning):

Locating holes Ø 3mm H7, depth 3 mm

White arrows (mounting):

Threaded holes M2.5, depth 9 mm

Gray arrows (mounting):

Threaded holes M3, depth 6 mm

Tools and Accessories

■

At least 3 screws with suitable dimensions

■

Suitable tools for tightening the screws

■

Optional: 2 dowel pins with suitable dimensions as locating pins for aligning the load on
the V-408

Requirements

✓

You have read and understood the

general safety instructions (p. 8)

✓

You have mounted the V-408

onto a surface (p. 14)

properly.

✓

The motion platform of the V-408 is suitably fixed, e.g., by

attaching the transport

safeguard (p. 31)

✓

The V-408 is not connected to the electronics.

✓

You have prepared the load so that it can be fixed to the mounting holes on the motion
platform:

■

The distance between the center of gravity of the load and the center of the motion
platform is as small as possible in all directions.

■

At least three points are provided for fixing the load on the motion platform.

NOTICE

Impermissibly high load on the V-408

An impermissible high load on the motion platform impairs the motion and can damage the
V-408.

►

Pay attention to the

maximum permissible forces (p. 33)

that may act on the motion

platform.

►

In the case of multi-axis systems, include the masses of the positioners to be moved
when calculating the load.

NOTICE

Excessively long screws

The V-408 can be damaged by screws that are inserted too deeply.

►

Pay attention to the

depth of the mounting holes (p. 35)

►

Only use screws with the correct length for the respective mounting holes.

Fixing the Load

1. If necessary: Insert the locating pins into the corresponding holes in the motion platform.
2. Align the load on the motion platform so that the mounting holes selected in the motion

platform can be used for mounting the load.

3. Place the load onto the motion platform so that the locating pins are inserted into the

corresponding locating holes in the load.

4. Tighten the screws in all mounting holes.
5. Check that the load is fixed firmly to the motion platform.

6 INSTALLATION

V408M0001EN

‒

2/17/2020

M O T I O N | P O S I T I O N I N G

Содержание PIMag V-408













































Результаты поиска

Содержание PIMag V-408

Отзывы:

Похожие инструкции для PIMag V-408

Бренды по названию

Популярные бренды

PI PIMag V-408, Руководство пользователя

Результаты поиска

Содержание PIMag V-408

Отзывы:

Похожие инструкции для PIMag V-408

Бренды по названию

Популярные бренды