background image

CAUTION

Dangerous situation

Failure to observe can lead to minor injury.

Actions to take to avoid the risk.

NOTICE

Dangerous situation

Failure to observe can lead to material damage.

Action to take to avoid the risk.

Information

Additional information on the L-412.xx9211E0 that can affect your application.

2.3

Figures

For better understandability, the colors, proportions and degree of detail in illustrations can
deviate from the actual circumstances. Photographic illustrations may also differ and must
not be seen as guaranteed properties.

2.4

Downloading Manuals

The latest versions of the user manuals can be 

downloaded (p. 6)

 at 

www.pi.ws

.

For products that are supplied with software (data storage device in the scope of delivery),
access to the manuals is protected by a password. Protected content is only displayed on the
website after entering the access data. You need the data storage device for the product to
get the access data.
If a manual is missing or problems occur with downloading, contact our 

customer service

department (p. 26)

.

Downloading Manuals

1. Open the website 

www.pi.ws

.

2. If the product was shipped with a data storage device: Log into the website:

a) Click 

Login

.

b) Enter the login data.

The login data is in the 

[...]_Releasenews_[...].pdf

 in the 

Manuals

 directory on the

data storage device.
If necessary: Follow the link and register yourself to get the login data.

c) Click 

Login

 or press the Enter key.

3. Search for the product:

a) Click 

Search

.

b) Enter the product number up to the period (e.g., L-412) into the search field.
c) Click 

Start search

 or press the Enter key.

d) If necessary: Click 

Load more results

 at the bottom of the list.

4. Click the corresponding product in the list of search results.
5. Click the 

Downloads

 tab.

The manuals are shown under 

Documentation

.

6. Click the desired manual and save it.

2  ABOUT THIS DOCUMENT

L412M0016EN 

 3/14/2019

6

M O T I O N   |   P O S I T I O N I N G

Содержание L-412.039211E0









































Отзывы: