PI Micos L-731 Series Скачать руководство пользователя

Страница: 21 / 57

5 Installation

L-731 / V-731 Precision XY Positioner

MP158D

Version: 1.0.1

5.1

General Notes on Installation

DANGER

For V-731 models: Magnetic fields!

Magnetic fields may damage or interfere with sensitive devices and objects (e. g.

cardiac

pacemakers

, EC-cards, magnetic data carriers).

The fields are also effective when the

positioner is not connected to the controller/electric power.

Loose magnetizable objects (e.g. made of iron, steel) may be attracted and cause damages. The

corresponding pull might not be manually compensated.



If applicable, note the usual precautions for applying pacemakers.



Remove loose magnetizable objects and sensitive devices from the installation site.



Ensure that hazardous areas are marked correspondingly and that the usual precautions

are applied.



Keep sufficient distance from the positioner.



Apply corresponding precautions also for storage and transport of the positioner.

CAUTION

Risk of crushing by moving parts!

There is a risk of minor injury from crushing between the moving parts of the positioner or the

load and a fixed part or obstacle.



Use protective structures to keep limbs away from areas in which they could be caught by

moving parts.



Observe the safety distances in accordance with DIN EN ISO 13857 when installing

protective structures.

NOTICE

Cable break!

A cable break leads to failure of the positioner.



Install the positioner so that the cable is not bent too strongly or crushed.

NOTICE

Heating up of the L-731 / V-731 during operation!

The heat produced during operation of the L-731 / V-731 can affect your application.



Install the L-731 / V-731 so that the application is not impaired by the dissipated heat.

Installation

Содержание L-731 Series


























































Результаты поиска

Содержание L-731 Series

Отзывы:

Похожие инструкции для L-731 Series

Бренды по названию

Популярные бренды

PI Micos L-731 Series, Руководство пользователя

Результаты поиска

Содержание L-731 Series

Отзывы:

Похожие инструкции для L-731 Series

Бренды по названию

Популярные бренды