manualshive.com logo in svg

Phytec phyCORE-XScale/PXA255, Примечание к применению

Поделиться
Скачать
Phytec phyCORE-XScale/PXA255 Скачать руководство пользователя страница 2

Application Note

                                                                                                                                                

                                                                                                                                                

 PHYTEC Technologie Holding AG 2004

Europe: Support Hotline: +49 (6131) 9221-31 

 http://www.phytec.de

North America: Support Hotline:  1-800-278-9913 

http://www.phytec.com

LAN-032e_2

2/8

All PHYTEC hardware components are included in the
phyCORE-PXA255 Basic Development Kit (part #
KPCM-022-200E-B).

1.2

 

Software Description and Requirements

This Application Note for the phyCORE-PXA255 requires the use of
a terminal program on the host-PC, such as Komport or Minicom for
Linux, together with TFTP services.

The Bootloader used for downloading the Linux kernel is the
Universal Bootloader U-Boot. The Bootloader is pre-installed on the
phyCORE-PXA255 and resides in the on-board Flash memory from
address 0 to 0x40000.

A description of this Bootloader can be found at:
http://sourceforge.net/projects/u-boot/

Содержание phyCORE-XScale/PXA255









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды