CURE L
2. SAFETY RULES
3. SAFETY DEVICES
5. INTENDED USES
4. ENVIRONMENTAL
PROTECTION
6.
SETTING UP YOUR
NEW MACHINE FOR
THE FIRST TIME
7.
BEFORE STARTING
YOUR MACHINE
8.
STARTING AND
STOPPING YOUR
MACHINE
9.
MAINTENANCE AND
CARE OF YOUR
MACHINE
Warning:
Under no circumstances must the
machine be operated with the door
open.
Danger:
Risk of injury; unexpected start up
and electrical shock.
Always disconnect the mains power
supply before commencing ANY
cleaning or maintenance on this
machine.
Danger:
Risk of injury by unexpected start up
and electrical shock
Always disconnect the mains power
supply before commencing ANY
maintenance on this machine.
Have any electrical problems checked
by a qualified engineer.
Danger:
Never circumvent the door safety
switch as the LED unit will cause
severe damage to your eyes.
Caution:
Possible hazardous situation that
could lead to mild injury to persons or
damage to property.
This machine is 64 kgs (140 pounds)
and we recommend that 2 persons
move this machine to its final
placement.
When the machine is positioned
unpack the glass shelf and place
it inside the unit resting it on the 6
support pads.
Locate the mains plug lead and plug
it into the socket on the rear of the
machine, push the plug in and twist to
the right to engage the power.
This machine is intended to Cure 3D printed parts
only inside its enclosure,
This machine in not intended to work outside without
suitable protection.
Electrical section
This machine may only be connected to an electrical
supply which has been installed in accordance with all
relevant IEC regulations.
This machine has been developed to work on any
power supply from 105v to 240v AC.
Never permanently connect this machine to the mains
supply without an isolating switch.
Always check the mains cable for damage prior to use.
Only authorised persons may replace damaged cables
to this machine.
Starting/Loading
On the front of the machine you will see the green
on/off rocker switch (2) press it in at the bottom and
it will light up turning the machine control circuits on.
The machine will not be operated if the door is open
To start the UV cure program, twist the timer switch
(7) fully clockwise, this will work for 2 hours (you can
alter this time down to suit your own needs).
When the timer is ON a small red flashing light (5)
is shown on the control panel, a yellow light (6) is
indicated when the heater is working.
Temperature settings:
The machines temperature is factory set to a
maximum of 65°c. If you wish to use a lower
setting you can by pressing the set button on the
temperature unit once, then pressing the down
button you can set your machine to the desired
working temperature. Depending on the country and
voltage of your machine the heat-up time will vary
from 5-25 minutes, to ensure accurate and precise
curing you will need to wait until the temperature
has reached the selected setting before loading the
prints into the unit.
Loading:
Open the door and using suitable heat resistant
gloves place the print platform onto the hanging
bracket (8). Close the door and reset the timer to 2
hours.
Unloading:
Open the door and using suitable heat resistant
gloves remove the print platform from the hanging
bracket and close the door to maintain the Cure L’s
temperature.
If you are NOT going to place another printed part
into the unit straightaway, do not close the door
but you must leave the green switch on to allow the
heating elements to cool down
Daily checks
Ensure that the inside of the machine is kept clean
especially the glass covering the UV lights.
Check the condition of the door seal.
Check the mains cable.
Make sure that the vents on top of the machine are
not covered over.
Machine fails to start
Does the green switch light come ON?
If no, confirm that you have a working power supply.
To do this check the fuse in the plug.
If the fuse in the plug is OK then you need to call an
engineer
Machine has power but the heater fails to work
Check the fuse on the left-hand side of the machine
(8 amp)
If the fuse is OK call an engineer.
Machine has power but the lights fail to come on
Check the fuse on the left-hand side (2 amp)
If the fuse is OK call an engineer.
10. TROUBLESHOOTING
Recycle:
Most of the packaging material can
be recycled. Please do not throw the
packaging material in to a domestic
household waste system, send it for
recycling.
Recycle:
Remove the outer packaging and
recycle it.
Recycle:
Old machines contain valuable
materials that can be reused or
recycled; please send your old
machines to a suitable recycling
centre at the end of its lifespan.
3
4
CURE L