Phonic SMARTMAN 303A Скачать руководство пользователя страница 12

8

SMARTMAN 303A / SMARTMAN 703A

English    

OUTPUT

The Smartman has two main outputs. The first is the “Amp” 

output, consisting of all signals sent out through the speaker. 

The second is the “Main” output, which is sent through the 

line-level stereo outputs found on the rear of the Smartman. 
In addition to these outputs, the Smartman offers the USB 

Record output. As the name suggests, these signals are 

sent directly to the USB Recorder.
The button at the top of each output strip can be touched 

to enter into the individual signal processor pages. These 

pages then have a “back” arrow on the top right-hand side 

that will return you to the main Output page.

Main L+R or L/R Switch: 

While the Smartman has a 

physical switch on the rear, the software also features a 

switch that allows adjustment of the rear-panel outputs 

between L+R and L/R. When set to L+R, the outputs will 

essentially be mono. The left and right signals will be 

combined and sent out of both the left and right outputs. 

The L/R position means the left and right signals will be 

separated and sent out their respective outputs.

On Button: 

The on buttons essentially allows the 

corresponding output mix to be activated and deactivated.

Faders:

 Like the input mixes described on the previous 

page, the output mixes each have their own “virtual 

faders.”

SIGNAL PROCESSORS

Each of the output mixes has its own independent signal 

processors. The Main output mix features a low-pass 

filter (LPF), delay and dynamic function. The Amp output 

features both delay and dynamics. 

LPF:

 The low-pass filter found on the Main outputs 

features  an  individual  ‘ON’  button  for  each  the  left  and 

right output mixes.  This will allow all low-frequency audio 

to pass through while removing high frequency, making 

the signal perfect for use with subwoofers. The frequency 

control that accompanies the LPF on/off buttons allows 

the cut-off frequency to be adjusted between 20 and 

502Hz. Audio above the cut-off frequency is removed at a 

rate of 12dB/octave.

Delay:

 The delay button allows users to activate a delay 

on the currently selected output. Adding a delay to output 

channels can help to compensate for distance between 

speakers in large multi-speaker setups. A delay time of 

one millisecond per foot (or 3 milliseconds per meter) that 

the speaker is away from the stage is the general rule of 

thumb in this application. This, however, is not always the 

case. Thankfully, the Smartman allows the delay time to 

be set in “meters’ or “feet” instead of “milliseconds”, taking 

a lot of the guesswork out of the setup. 

Содержание SMARTMAN 303A













































Отзывы: