Phonic POWERPOD 1082, Руководство пользователя

Страница: 13 / 24

POWERPOD1080/1082 USER’ S MANUAL PHONIC CORPORATION
MASTER SECTION DESCRIPTION
Page 13
1) Position the sliders at “ 0.”
2) Connect source to the input channel and set
the input level by adjusting the LEVEL knob.
3) Gradually turn up signal level by turning the
LEVEL knob 19 , MASTER knobs of MAIN
L/R and MONITOR clockwise until you en-
counter feedback (BE CAREFUL, FEEDBACK
MAY OCCURRED SUDDENLY).
4) Proper adjustment of the built-in 7-band EQ
helps to reduce the chance of producing feed-
back.
Sound Quality:
Push up the 60Hz slider deepens the bass and
increases the feel of the low frequencies.
Over adjust the 120Hz slider may cause certain
degree of distortion.
Over adjust the 360Hz slider may produce noise.
Proper amount of 1KHz frequency gain could
help make sound to become more live and vivid.
Over adjust the 2.5KHz slider may cause cer-
tain degree of distortion.
Over adjust the 7KHz slider may cause “ hiss”
sound.
Proper amount of the 16KHz frequency could
add clarity.
28 AUX IN
This rotary knob controls the level of the input
signal from the AUX IN socket 8 . Input signal
then is sent to the MAIN L/R 31 .
29 TAPE IN
This rotary knob controls the input level of the
r e c e i v e d s i g n a l f r o m t h e TA P E I N s t e r e o
input 9 . While TAPE IN can be connected to
CD, DAT, MD, tape players and etc. for playback,
REC OUT can be used with CD, DAT, MD, tape
recorders and etc. for recording purposes.
30 MONITOR LEVEL KNOB & METER
This section consists of signal level meter and
level knob. The MASTER knob controls the sig-
nal level of MONITOR output. The 7-band equal-
izer at its left-hand side can affect the final out-
put of the MONITOR. The level meter is made
of 6-segment LEDs, including 2 green and 3
yellow, metering from -10dBu to +6dBu, offer you
a visual display of the signal level of MONITOR
output. PowerPod 1080 also comes with a lim-
iter in this section. The LIMITER LED comes on
when limiter kicks in to prevent overload and
peak.
31 MAIN L/R LEVEL KNOB & METER
This section consists of signal level meter, level
knob and LIMITER LED. The MASTER knob
controls the signal level of MAIN L/R output. The
7-band equalizer at its left-hand side can affect
the final output of the MONITOR. The level
meter is made of 10-segment LEDs, including 2
green, 3 yellow and 1 red (LIMITER) for each of
the L and R channels, metering from -10dBu to
+6dBu, offer you a visual display of the signal
level of MAIN L/R output. The LIMITER LED
comes on when limiter kicks in to prevent over-
load and peak.
32 POWER
The blue light comes on when the unit has power
(POWER button is in the back).
33 PHANTOM POWER
Push the PHANTOM POWER switch up to send
+48 Phantom Power to Lo-Z (low impedance)
and MIC inputs. Condenser microphones need
phantom power or a direct box to function. Thus
phantom power must be on when using con-
denser microphones. Turn down the LEVEL
knob before turning on phantom power. Always
plug in microphones before turning on phantom
power. This way you can prevent harming your
equipment as well as avoid produce unwanted
noise. The red LED besides the switch will light
when the Phantom Power is on.
34 Amplification Mode
WARNING! Make sure to turn off t h e u n i t ’s
power before using this function.
3 AMPs for PowerPod 1080
This unit comes with 3 built-in 270-watt amplifi-