background image

 

Setup Wizard 

 

The Setup Wizard is used to configure the type of unit, the 
input settings (type, level, and phantom selection) and setup 
the output level. Additional settings are available through the 
audio setup utility. Those include 3-way settings, color 
(frequency response) settings, and more, and will be 
detailed in the next chapter.  
 
Setting the units is performed one unit at a time. Plug your 
Laptop to the USB port of the unit being set and run the 
Setup Wizard software. We recommend that you start with 
the lower ranked units (to which the Matrix microphones are 
connected) and go up the ladder. Please note that in order 
for the Beamforming algorithm to perform properly all the 
microphones participating in the matrix have to have the 
same sensitivity. Therefore when you setup any microphone, 
all the microphones connected to the same unit will 
automatically be set to the same sensitivity level. 
Furthermore – in a Multi-Unit setting, when you set the next 
Slave unit the software remembers the last microphone 
setup and will recommend that you use the same 
parameters (and will copy / paste them for you). If you 
change the settings of a microphone along the way the 
software will recommend that you go back to previously set 
Slave units and reset them with the new level. 
 
The opening screen of the Wizard program sets up the unit 
type. You can select one of three types: Stand Alone, Master 
or Slave. If your unit has previously been programmed the 
wizard program tells you which type the unit is set to, and 
allows you to either keep it or change it. 
 

 
If the unit is mid rank unit (not the lowest Slave and not the 
Master) then it should be set to be a Slave. 
 
The following paragraphs detail the setup steps for each of 
the Octopus’s types. Since some of the setting screens in 
various types are similar, the Stand Alone setup is the most 
detailed and we recommend that you read through it even if 
you are not setting your system as such.  

 
Setting a Stand Alone unit 

SA units include all the connections (inputs, outputs and far-
end) therefore you will be guided though the setting of the 
loudspeakers’ volume, the microphones and the output. 
 
In the first step you are setting the room’s loudspeakers 
volume. You can play either a music file or speech and setup 
the speakers’ volume to the wanted level. 

Phoenix Audio Technologies                                          

 

 

www.phnxaudio.com 

11

Содержание Octopus

















Отзывы: