Used to connect the amplifier to speakers.
Minimum speaker cable size is 16 gauge (PG#
SS162 or QS162). Use the left + and right -
terminals for bridged mode. Minimum
impedance is
2 ohms bridged
OR
1 ohm
stereo
.
Used to connect the amplifier to the
vehicle's battery. Minimum power cable
size is 8 gauge. This cable must be fused
within 18" of the positive battery terminal.
Used to connect the amplifier to the
vehicle's chassis. Minimum ground cable
size is 8 gauge. Keep the cable as short
as possible.
DO NOT
connect directly to
the negative battery terminal.
Used to turn the amplifier on and off with
the headunit. Minimum turn-on wire size
is 18 gauge.
Used to protect the amplifier's power
supply from improper connection (reversed
B+ and B-). The fuse located on the right
or closest to the power terminals is used
to protect the amplifier, while the fuse
located to the left or closest to the speaker
terminals is a spare replacement fuse. If
replacement is necessary, use the same
size and type. Use one 30 amp ATO style
fuse.
Never use a fuse with a higher amp rating.
This LED turns on whenever the amplifier is
on. The amplifier cannot turn on unless it is
grounded through the B- terminal and receiving
12 volts at both the B+ and R terminals. The
LED will turn amber if the amplifier shuts down
due to overheating (thermal).
Connect speaker wires from a headunit without
pre-amp level outputs directly to these terminals
using the supplied .187" female spade
connectors. Maximum input power is 35 watts
per channel.
Used to boost the amplifier's output from
0 to +18dB at 45Hz.
Used to reach maximum amplifier power
with a wide variety of headunits.
The amplifier is more sensitive to input
signals when set to .1 and less sensitive
when set to 3.
Connect pre-amp signal cables from the
headunit directly to these terminals. We
recommend using Phoenix Gold QLX or TRX
twisted pair interconnects.
Provides a Full Range signal for an
additional amplifier. The External Output
signal is unaffected by the crossover select
switch.
This switch controls the type of signal that
reaches the speaker ouputs. For a High
pass signal fixed at 125 Hz set the switch
to HP. For Low pass signal fixed at 90 Hz
set the switch to LP. To bypass the
crossover for Full Range signal set the
switch to BYPASS.
•
•
•
BYPASS
HP
LP
R
L
INPUT
MADE IN AMERICA
HI LEVEL
R+
L+ L-
R-
•
•
•
SENS BASS
3
.1 0 18
•
30A
B+
R
L +
R +
PWR
B–
L –
R –
AMBR-THL
SPEAKER
BRIDGED
+
–
EXT
OUTPUT
R+
L+ L-
R-
BAT
ACC
CHANGER
ANTENNA
R
L
R(+)
L(+)
Line-Level:
Connect high quality RCA style signal cables to the
inputs jacks. Use both left
and
right input jacks for stereo, bridged
or Tri-Mode operation. For maximum noise rejection, we
recommend Phoenix Gold QLX or TRX twisted pair signal cables.
Hi-Level:
Connect the positive hi-leveI inputs to the headunit's
positive speaker outputs. Connect the negative hi-leveI inputs to
the headunit's negative speaker outputs.
R(-)
L(-)
QLX or TRX
Twisted Pair
Interconnects
Note:
Never use hi-level and line-level inputs at the same time.
Maximum hi-level input power:
35 watts per channel
Supplied .187"
Quick Disconnect
Terminals
SS182 18 Gauge
Speaker Cable
Left
Right
R
L
INPUT
HI LEVEL
EXT
OUTPUT
•
•
•
BYPASS
HP
LP
Содержание XS 2200
Страница 6: ......
