background image

Amplifier Owner’s Manual

www.phoenixgold.com  

SPECIFICATIONS

SD800.4 SPECIFICATIONS

Frequency Response: 

             ± 1dB from 20Hz to 20kHz

Signal to Noise Ratio: 

             >100dB

High and Low Pass Crossovers: 

             12dB per Octave

Crossover Range: 

             40Hz to 400Hz

Bass Boost @ 45Hz:                                               0 to +18dB

Low Level Input Range: 

             200 millivolts to 8 volts

Lowest Recommend Load: 

             4 ohms Bridged/2 ohms Stereo

Typical Efficiency: 

             80%

Damping Factor 

             Greater than 200

RMS Power Output 

125w x 4 @ 4 ohms Stereo

 

200w x 4 @ 2 ohms Stereo

 

400w x 2 @ 4 ohms Bridged

Power/Ground Wire Size: 

4 Gauge

Recommend Power Wire Fuse:  

       60a

Dimensions (Includes Mounting Feet):  11.0” L x 6.9” W x 2.0” H

 

        279mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):           11.6” L x 6.9” W x 2.0” H

 

        295mm L x 176mm W x 51mm H

SUBWOOFER CHANNEL:

Frequency Response:  

± 1dB from 20Hz to 300Hz

Signal to Noise Ratio:  

>100dB

Low Pass Crossover:  

12dB per Octave

Low Pass Crossover Range:  

30Hz to 300Hz

Bass Boost @ 45Hz:  

0 to +18dB

Low Level Input Range:  

200 millivolts to 8 volts

Lowest Recommend Load:  

2 ohms

Typical Efficiency:  

80%

Damping Factor:  

Greater than 200

SD1100.5 SPECIFICATIONS

FRONT AND REAR CHANNELS:

Frequency Response: 

             ± 1dB from 20Hz to 20kHz

Signal to Noise Ratio: 

             >100dB

High and Low Pass Crossovers: 

             12dB per Octave

Front/Rear High Pass Crossover Range:        15Hz to 250Hz

Low Level Input Range: 

             200 millivolts to 8 volts

Lowest Recommend Load: 

             4 ohms Bridged/2 ohms Stereo

Typical Efficiency: 

             80%

Damping Factor 

             Greater than 200

RMS Power Output 

        200w x 1 @ 4 ohms 

 

        300w x 1 @ 2 ohms

Recommend Power Wire Fuse:  

80a 

Power/Ground Wire Size: 

4 Gauge

Dimensions (Includes Mounting Feet):  12.2” L x 6.9” W x 2.0” H

 

        309mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):           12.8” L x 6.9” W x 2.0” H

 

        325mm L x 176mm W x 51mm H

RMS Power Output 

125w x 4 @ 4 ohms Stereo

 

200w x 4 @ 2 ohms Stereo

 

400w x 2 @ 4 ohms Bridged

 

POWER OUTPUT NOTE: A power birth certificate is included for each amplifier. SD 

amplifiers are conservatively rated and will exceed their RMS power rating shown 

here. All RMS power ratings and measurements are at 14.4 volts with no more than 

1% THD. SD800.4 and SD1100.5 feature ADAPT technology which provides the 

same power output from 11 to 15 volts with music material. 

Содержание SD1100.5













Отзывы: