Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 92

Страница: 92 / 112

IB IL 24 PSDO 8-PAC

92 / 112

PHOENIX CONTACT

7619_en_05

F-System

Failsafe system

A failsafe system is a system that remains in the safe state or immediately enters a safe state

when specific failures occur.

iParameter

Individual safety parameter of a device

Passivation

If the safety module (F-I/O device) detects an error, it switches the affected channel or all

channels of the module to the safe state; the channels are then passivated. The detected

errors are reported to the safe controller.

For a safe input module when the F-System is passivated, instead of the process values

present at the safe inputs, (0) substitute values are provided for the safety program.

For a safe output module when the F-System is passivated, instead of the output values pro-

vided by the safety program, substitute values (0) are transferred to the safe outputs.

PROFIsafe

Safety-related bus profile based on PROFIBUS DP or PROFINET. It defines the communi-

cation between a safety program and the safe I/O device (F-I/O device) in a safe system (F-

System).

PROFIsafe address

Each safe module has a PROFIsafe address. This address must be set on the safety module

(F-I/O device) via DIP switches and then configured in the configuration tool for the safe con-

troller used.

PROFIsafe monitoring

time

Monitoring time for safety-related communication between the safe controller (F-CPU) and

safe I/O device (F-I/O device).

This time is parameterized in the F_WD_Time F-Parameter.

Consecutive number

See "Consecutive number"

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 92 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: