Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 91

Страница: 91 / 112

7619_en_05

PHOENIX CONTACT

91 / 112

A Appendix: PROFIsafe terms used in the user manual

Some of the terms that are used in connection with PROFIsafe in this user manual are de-

scribed below.

A definition of PROFIsafe terms is also provided in the PROFIsafe profile.

CRC

Cyclic Redundancy Check

A cyclic redundancy check is used to verify the validity of the process data contained in the

safety telegram, check whether the assigned address relationships are correct, and verify

the safety-related parameters. This value is part of the safety telegram.

Consecutive number

Consecutive number

Method for ensuring that the safe data is transmitted completely and in the correct order.

F-Parameter

(According to PROFIsafe system description, Version 09, November 2007)

F-Parameters contain information for adapting the PROFIsafe layer to specific customer

specifications and for checking the parameterization by means of a separate method (di-

verse). The main F-Parameters are:

F-CPU

Failsafe controller, safe controller

F_Destination_Address

F-Parameter; PROFIsafe destination address; address of the safe device

(see also "F-Parameter")

F-I/O device

Failsafe I/O device; safe input and/or output modules

Modules with integrated safety functions, which are approved for safety-related operation.

F-Slave

Failsafe slave

F-Source_Address

F-Parameter, PROFIsafe source address; address of the safe controller

(see also "F-Parameter")

F_S/D_Address

(F-Address for

short)

A unique address for F-Devices within a PROFIsafe island. The

technology part of the F-Device compares the value with the ad-

dress switch locally or with an assigned F-Address in order to check

the authenticity of the connection.

F_WD_Time

Specifies the millisecond value for the watchdog timer. The timer

monitors the time that elapses until the next valid PROFIsafe mes-

sage is received.

F_SIL

Indicates the SIL that the user can expect from the relevant F-De-

vice. It is compared with the manufacturer's specification that is

stored locally.

F_iPar_CRC

A checksum that is calculated from all iParameters of the technol-

ogy-specific part of the F-Device.

F_Par_CRC

A CRC signature which is created via all F-Parameters and ensures

error-free transmission of the F-Parameters.

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 91 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: