background image

 

11

III.

 

Power supply: 

P150TR need to use external AC-DC adaptor 
Wall mount type power adaptor,    Input: 100~240AC 0.9A, Output: 12Vdc 3.0A 
Power consumption 
Normal   

 

: <18W typ. (with keyboard, mouse connected). 

Power save / off 

: 2W max. (Down-stream ports not connected) 

 

IV.

 

USB Hub: 

USB 2.0 Hub 
x1 USB A type downstream port 
x1 Mini USB B type downstream port

 

 

V.

 

For your safety: 

 

When move the monitor, always disconnect USB cable and/or external power adaptor to avoid 

any danger. 

 

Please use the power and signal cables correctly when install it. 

 

In case of notice any abnormal smell or noise, please stop operation and call the nearest dealer 

or service center. 
 

VI.

 

Support timing chart: 

 

Timing 

Mode 

Reference 

Standard 

Resolution 

Pixel 
MHz 

FH KHz 

FV Hz  Interlace 

Polarity 

Polarity 

XGA 

VESA 

1024 x 768  65.000  48.363  60.004 

NO 

− 

 

 

VII.

 

Resistive Touch Panel:   

Panel: 

Type  

 

 

 

 

 

 

: Five-Wires Analog Resistive 

Input Mode   

 

 

 

 

 

: Stylus or Fingers 

Transparency   

 

 

 

 

: 80% +/- 5% 

Build-in Touch Control Module:   

 

 

(Note: For Panel Touch Control, user need to connect upstream cable to System PC)

 

Control type   

 

 

 

 

: USB 

Touch Control Driver 

 

 

 

 

: eGalax Touch Driver

 

 

 

 

 

 
 
 

Содержание P150TR














Отзывы: