Philips Selecon PL3 LED Luminaires Скачать руководство пользователя страница 31

Страница: 31 / 36

Infrared Remote Control Overview

PL3 LED Luminaires

Installation & User’s Manual

To select and program PL3 LED luminaire with PL3IRR remote:

Note:

The IR, on the PL3 LED luminaire, must be set to "Enabled" in order for the PL3IRR remote to communicate

and control the fixture. Each luminaire to be programmed/adjusted needs to be selected and programmed/adjusted
individually.

Step 1. Aim PL3IRR programming remote (as shown in

Figure 4

) and press "Enter" button. Luminaire will flash an

LED (at bottom of unit) to provide a target for the laser to aim at. Luminaire will look for laser beam (from
PL3IRR) to enter selected mode.

Figure 4: PL3 LED Luminaire Programming / Control

Step 2. Point PL3IRR remote directly at luminaire IR window and press "Laser" button. Luminaire to be

programmed or adjusted is now selected.

Note:

At luminaire IR port, a Blue LED will illuminate when the fixture is in programming mode and blink Red when

buttons are pressed on IR remote to confirm it sees the remote and is receiving commands.

Step 3. Set luminaire to preset or make adjustments as desired.

Step 4. To save settings, press "Learn" button and then press any Preset button (except Off . Off cannot be

programmed). Preset is now saved. To cancel programming, press "Cancel" button.

Step 5. After programming or adjustments are complete, press "Exit" button. Repeat, as desired, on additional

luminaires to be programmed/adjusted.

PL3 LED Luminaire

PL3 Luminaire IR Port

(located underneath luminaire)

PL3IRR Remote Control

Содержание Selecon PL3 LED Luminaires





































Результаты поиска

Содержание Selecon PL3 LED Luminaires

Отзывы:

Похожие инструкции для Selecon PL3 LED Luminaires

Бренды по названию

Популярные бренды

Philips Selecon PL3 LED Luminaires, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Selecon PL3 LED Luminaires

Отзывы:

Похожие инструкции для Selecon PL3 LED Luminaires

Бренды по названию

Популярные бренды