Product
Specifications
MHPWDC2020H
Operating Voltage: 120VAC, 50/60Hz
Number of Circuits: 2
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit):
OPT2200F: 2000VA
OPT22000F15: 1800VA
Operating Voltage: 277VAC, 60Hz
Number of Circuits:
OPT24000F7: 2
Min. Rated Load (per circuit): 35W
Max Rated Load (per circuit):
OPT24000F7: 4000VA
Supported Load Types: 3-Wire Phase Control Fluorescent
dimming ballasts
Cooling: Natural convection
Ambient Operating Temp: 0 to 40 degrees C
Relative Humidity: 5 to 95% (non-condensing)
3-W
IRE
F
LUORESCENT
D
IMMER
M
ODULES
Installation
Instructions
The Optio 3-Wire Fluorescent Dimmer Modules offer reliable dimming of 3-wire phase control
dimming ballasts where two wires are used for hot and neutral, and a third wire carries the phase
control signal. (For control of Lightolier Controls PowerSpec HDF dimming ballasts, use an Optio
"HDF" series module).
All Optio Dimmer Modules have identical mounting dimensions, allowing them to be easily swapped
within any of the Optio Lighting Control Panels. (Use caution to ensure that quad dimmer modules
are not installed into module spaces wired for dual dimmer modules.)
Description
WARNING
: Installing the module with power applied to the cabinet may expose you to
dangerous voltage and damage the device. Remove power before installing. A qualified
electrician should perform this installation.
Any combination of Optio dimming and relay modules may be installed in the Lighting Control Panel.
Blank covers MUST be installed in any unused spaces. Pull the jumper (shorting plugs) before
installing.
To install modules:
1. Unpack module and recycle or properly discard packaging materials. (Be sure to keep this
instruction sheet for future use.) Inspect dimming module for signs of damage during transit.
2. Disconnect main power to Optio Lighting Control Panel.
3. Open dimmer module side of panel front cover.
4. If present, remove blank cover from location where module is to be installed (
Figure 1
).
When possible, lower modules should be installed first.
5. Remove shorting plugs from the load terminal block. (The shorting plug is the red tab
protruding from the green load terminal block. To remove, grasp the shorting plug and
gently pull.)
Note: The dimmer module will not operate properly if the shorting plug
is left in circuit.
6. Gently insert module into lighting control panel, heatsink first. Secure module using four
screws (provided). Dimmer Module should be installed with the heatsink facing away from
you.
Note: The connectors of 277VAC Optio modules are keyed, preventing the insertion
of modules into panels of the incorrect voltage. Do not force modules into slots.
7. Connect control wire from fluorescent dimming ballast to appropriate terminals on panel.
8. Close panel front cover.
Blank Cover
Dimmer
Module
Screw (4)
Screw (4)
Load Terminal Block
Focus Button
& Status LEDs
Shorting
Plug
Terminal
DETAIL
Figure 1: Installing Modules and Blank Covers
Installation Procedure
NOTE: The Optio 9-Module
Panel is used to illustrate the
installation. However, the
module installation is identical
for all Lighting Control Panel
models.
Electrical Specifications
Operation
Optio Dimmer Modules are
equipped with a "Focus Button" on
each circuit (
Figure 1
). Tapping
the focus button quickly will turn the
circuit on to full, tapping it quickly
again will turn the circuit off.
Pressing and holding the focus but-
ton will ramp the dimmer up to full
intensity. If the focus button is
released before reaching full inten-
sity, the dimmer will stop at that rel-
ative output.
Red LED
Green LED
Condition
Off
Off
Normal
Off
Flashing
No Load
Off
On
Focus Mode
(controlled at dimmer)
Slow Flashing
Off
Overload
Fast Flashing
Off
Over Temperature
On
Off
Communication Error
Flashing
Flashing
Miswire to Line
Status LED Indications:
Philips Lighting Controls
2828 Trade Center Drive, Suite 130B
Carrollton, Texas 75007
Technical/Sales assistance: 1-800-526-2731
Made in U.S.A.
www.philipslightiingcontrols.com P/N 85-6358B
Figure 2: Ballast Wiring Connections
TERMINAL A
Switched A
Leg (Hot)
Dimmer A
Control
TERMINAL B
Switched B
Leg (Hot)
Dimmer B
Control
