"VOL -" (RC)
Button pressed?
N
DVD DEALER
TEST
STEP
1
2
3
4
5
6
ACTION
Check the correctness of the
checksum of the flash.
S2B Echo Mode.
(This test is executed very fast
and hence user will not be able
to see this display message)
Check the correctness of the
IIC bus to the NVRAM.
(This test need about 3 minutes
to perform)
Check writing to the NVRAM.
Check writing to the SDRAM.
(This test is executed very fast
and hence user will not be able
to see this display message)
Result of all the tests.
Disconnect mains cord to exit
the Service Test Program.
DISPLAY
CHECKSUM
FLASH
S2B
ECHO
IIC
NVRAM
NVRAM
WRITE
SDRAM
WRITE
ALL TEST FAIL
or
ALL TEST PASS
DVD Dealer Test is used to check the flash RAM, the SDRAM,
the DRAM, the NVRAM and the I2C communication.
When all the tests are passed, display shows "ALL TEST PASS".
If at least one of the test fails, display shows "ALL TEST FAIL".
Y (Execute all the tests below without interaction)
ERROR
CODE
0601
1101
1102
1103
1104
1201
1202
1203
1204
1301
1302
1303
1304
1601
5401
5402
5403
5403
ERROR
DESCRIPTION
Calculated Checksum of FLASH is not correct
I2C bus busy before start
NVRAM access time-out
No NVRAM acknowledge
NVRAM reply time-out
I2C bus busy
Error sending I2C command to Slave
Slave controller not responding
Slave response is not correct
Parity error receiving data from Basic Engine
Parity error sending data to Basic Engine
No communication with Basic Engine
Comunication time-out with Basic Engine
The SDRAM is faulty
I2C bus busy
Error sending I2C command to Scart Switch IC
Scart switch IC not responding
Scart switch IC response is not correct
NUCLEUS
NUMBER
6
11
-
-
-
12
-
-
-
13
-
-
-
16
54
-
-
-
ERROR CODE (Nucleaus)
Table 4
ERROR CODE
00
01
10
11
ERROR CODE (Faulty Modules)
Table 3
STI + PERIPHERALS
OK
Faulty
OK
Faulty
BASIC ENGINE PART
OK
OK
Faulty
Faulty
"VOL +" (RC)
Button pressed?
Y
N
DVD PLAYER
TEST
STEP
1**
2**
3A**
3B**
4**
5
6
7
8**
9**
10**
11
12
13
14
15
ACTION
Output of a test picture on all available video
output devices.
Output of noise on all channels available.
Output of internally generated pink noise on all
channels available, test picture (internally
generated Colour Bar) on screen.
Press
S
(RC) to go to Step 3B.
Output of internally generated pink noise on all
channels available, test picture (external signal)
on screen.
Press
T
(RC) to return to Step 3A.
Sine sound output on all channels available.
The sound can be stopped by pressing the
"STOP"(RC) button.
Returns the Software Version of the basic
engine.
The user can move the tray in and out by
pressing "PLAY"(RC) or "RESUME"(RC) button.
User can insert or remove a disc.
The user can move the sledge in and out by
pressing "PLAY"(RC) or "RESUME"(RC) button.
The disc motor starts to run.
Focus Test.
Radial Test.
The laser spot jumps to another position.
Press "PLAY"(RC) to jump to the next position.
Press "RESUME"(RC) to jump to the previous
jump position.
The user can move the tray in and out by
pressing "PLAY"(RC) or "RESUME"(RC) button.
User can insert or remove a disc.
Reads out info from the error log (8 hex digits).
Up to 16 errors can be stored in a buffer.
The elements can be selected by pressing the
"PLAY"(RC) or "RESUME"(RC) button.
If the error log does not contain any fault codes,
"LO-00000000" will be displayed.
Shows all error bits. Selects the error bit by
pressing "PLAY"(RC) or "RESUME"(RC) button.
Runs the Dealer Test infinitely. The information
returned from the module will be displayed.
The loop number indicates the number of times
the loop test has been performed.
aa
- Error Code Faulty Modules (see Table 3)
bbb - Loop Number
cccc - Error Code Nucleaus (see Table 4)
Disconnect mains cord to exit the Service Test
Program.
DISPLAY
BAR
PICTURE
PINK
NOISE
SCART
LOOP DVD
SCART
LOOP EXT
SINE
SOUND
ENG-
"xx.yy.zz"
TRAY
SLEDGE
MOTOR
FOCUS
RADIAL
GROOVES
TRAY
LO-
"wwxxyyzz"
ERROR
"BITS xx"
"aa-bbb
cccc"
DVD Player Test is used to start several DVD specific tests.
At the end of the test, an error code "aa-bbb cccc" (see Step15) will be
shown that indicates which module(s) failed.
** User has to give a confirmation by triggering one of the following:
- If the test is OK, press "PLAY"(RC) button then follow by
T
(RC)
button to go to the next step.
- If the test is not OK, press "RESUME"(RC) button then follow by
T
(RC) button to go to the next step.
Note : By pressing only the
T
(RC) button to go to the next step without
triggering a confirmation, the test will be assume as OK by default.
Equipment required to run the DVD Player Test:
- television set
- 6 audio speakers
- an external video source
Go to next
step
by pressing
T
(RC)
"DIM" (RC)
Button pressed?
Y
N
DVD VERSION
MATRIX INFO
STEP
1
2
3
4
5
6
INFORMATION
Slash version number
Region code setting (Number 1 - 6)
Menu language table :
US/AP (USA-Asian Pacific language table)
US/EU (USA-Europe language table)
Audio/Subtitle language table
(Number 1 - 4)
Available of multichannel decording
Available of smart picture
Press
9
(RC) to exit
DISPLAY
SLASH ’###’
REGION ’#’
MULANG ’US/AP’
or
MULANG ’US/EU’
ASLANG ’#’
MULTI-CH ’YES’
or
MULTI-CH ’NO’
SMARTPIC ’YES’
or
SMARTPIC ’NO’
Choose step
by pressing
S
(RC)
T
(RC)
DVD Version Matrix Info is used to read the version matrix information
that are stored/defined in the DVD module software.
Y
N
Y
N
MUTE (RC)
Button pressed?
Software Version
Received?
DVD IIC
COMMUNICATION
TEST
Send request for
DVD Software Version
via IIC ports
Display shows
"DVD/www/xx.yy.zz"
Display shows
"FAIL"
Y
N
9
(RC)
Button pressed?
Y
N
DVD IIC Communication Test is used to test the IIC communication port
between the DVD module and the microprocessor of the set.
www
: refer to BEA Software version.
BEA = Back End Application (DVD Application Software).
xx.yy.zz : refer to Basic Engine Software version.
Basic Engine = part of the DVD module controlling the servo.
9
(RC)
Button pressed?
N
Y
DISC (RC)
Button pressed?
DVD SERVICE
TEST
Y
N
9
(RC)
Button pressed?
Display shows
"DVD SERVICE"
Remote Control (RC) must be in DVD source
before start of any DVD Service Test.
To start service test program
hold
T
& SOURCE
depressed while
plugging in the mains cord
Display shows the
ROM version
"S-Vyy"
(Main menu)
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
SERVICE TEST PROGRAM
LX7000SA & LX8000SA_Service Test Program_dd wk0232
3-2
3-2
www.freeservicemanuals.info
12/21/15
Published in Heiloo, Holland.