Philips IQ24 Скачать руководство пользователя страница 2

Страница: 2 / 8

Instructions for use

The Philips AVENT i

24 Electronic

Steam Steriliser is one of a new
generation of intelligent products
from Philips AVENT.

The i

24 Steriliser uses the intensive

heat of steam to eliminate harmful
bacteria helping you sterilise your baby
feeding equipment as safely and
quickly as possible. There are two
different modes for greater
convenience:

Mode 1

(Optional six hour mode)

runs a single 6 minute sterilising
cycle, then keeps the contents sterile
for 6 hours, providing the lid is
not removed.

Mode 2

keeps contents sterile for

up to 24 hours by continuously
repeating the cycle, so you can have
clean, sterile bottles day and night.

As well as bottles and breastfeeding
accessories, you can sterilise any
other boilable items (please refer
to the manufacturer’s instructions
regarding sterilisation).

Please take a few minutes to read
through the

ENTIRE INSTRUCTION

LEAFLET

before using your i

Steriliser for the first time.

PLEASE

SAVE THESE INSTRUCTIONS.

Also

available at

www.philips.com/AVENT

Remove all items from inside the
steriliser body.
1. Measure exactly 90ml of water

and pour in.

2. Assemble the blue components (baskets,

stem and bottle rack) and place into the
steriliser. Put the lid on.

3. Connect the lead into the back

of the steriliser and plug into the
mains supply.

4. The unit will display a flashing ‘0’ to

indicate you need to select a mode.
One short press of the control button
will display a flashing ‘1’. Hold the
control button in for 2 seconds then
release, and a rotating ‘0’ is displayed.
Mode 1 is now in progress.

5. After the water has reached 100°C,

it will turn to steam. When the
sterilising cycle is almost complete a
numerical countdown will be displayed
(see ‘Electronic Display Guide’).

6. At the end of the cycle the unit

will beep 5 times. Three bars will flash
and then remain displayed.

7. Let the steriliser cool down for 3

minutes. Turn off at the mains, unplug,
and disconnect the lead from the back
of the steriliser.

8. Remove the blue components and

empty any remaining water from the
unit. Wipe dry. The steriliser is now
ready for use.

Before using your steriliser for the first time

Before each use, wash items to be sterilised in
mild soapy water, and rinse.
1. Measure and pour in exactly 90ml of water

if selecting Mode 1

200ml of water if

selecting Mode 2.

2. Slide the lower basket onto the central stem.

Thread 2 screw rings onto the central stem.
Slide the bottle rack down the central stem,
with the neck facing down, until it rests on
the top screw ring.

3. Place the teats through the centre of the holes

in the bottle rack onto the lower basket.
Thread 4 screw rings onto the central stem.

4. Place inverted bottles in the bottle rack and

push the upper basket onto the central stem
until it rests on the catch. Place dome caps and
tongs into the upper basket.

The upper basket is not required when
sterilising 330ml bottles.

6. Place the assembled unit into the steriliser

body and put the lid on. Put the lead into the
back of the steriliser body and plug into the
mains supply. A flashing ‘0’ will appear,
indicating that you need to select a mode.

7. To select

Mode 1

, press the control button

once and the mode number will be displayed.
To run this mode, hold the control button in
for 2 seconds, then release. A rotating ‘0’ will
be displayed. Mode 1 is now in progress.

To select

Mode 2

, press the control button

twice and the mode number will be displayed.
To run this mode, hold the control button in

for 2 seconds, then release. Three ascending
and descending bars will be displayed. Mode 2
is now in progress.

8. Do not remove the lid until the 6 minute

sterilising cycle has ended. This is indicated by
5 beeps and 3 bars being displayed. It is
recommended to let the steriliser cool down
for 3 minutes after the sterilising cycle has
been completed. Items will remain sterile for
up to 6 hours provided the lid is not removed.
After 2 hours, the display will show 2 bars and,
after a further 2 hours, one bar. To indicate the
end of Mode 1 or 2, the unit will sound a long
beep followed by a flashing ‘0’ †. At this point
items should be used immediately or re-
sterilised. (Please refer to ‘To remove sterilised
items after a cycle’ on page 5). Switch off at
mains and unplug the lead from the back of
the steriliser. Pour away any remaining water,
rinse out the inside of the steriliser body and
wipe dry.

†

The end of a cycle is 6 hours after commencement

of Mode 1 and 24 hours after commencement of
Mode 2. The unit can be completely stopped at any
time during a cycle, by pressing and holding in the
control button for 2 seconds. The unit will beep and
a flashing ‘0’ will be displayed, indicating the unit
has returned to selection mode.

* to sterilise the ISIS Breast Pump or other items please refer

to page 5

Sterilising in Mode 1 –

6 hour sterile period

Sterilising in Mode 2 –

24 hour sterile period

To sterilise up to six 125ml, 260ml or 330ml AVENT Bottles*

Dishwasher Basket

Two baskets can be clipped together to hold small
items such as teats, breast pump parts etc. for
washing in the

top rack

of your dishwasher prior

to sterilisation.

To clip together, align the baskets so that the
indicators are opposite each other and snap the
baskets together. To open, pull apart with fingers.

When Mode 1 cycle is complete pressing the button
will reset the unit.

In Mode 2 (after sterilised) when 3x bars are
displayed, pressing the button will pause the cycle,
allowing removal/addition of item. Pressing the
button again will resume the cycle (re-sterilise). The
unit will immediately enter a new sterilisation phase
and continue the 24 hour cycle from where it was
interrupted.

If unplugged the 24hr cycle will stop.

Wash your hands thoroughly before removing the
sterilised items.

Remove the lid.

If necessary, shake excess water from items
before assembling.

The tongs can be used to remove small items and
to pull the sterile teats through the screw rings
of the bottles.

Removed items must be used/assembled immediately
or re-sterilised. Expressed milk can be stored in a
sterile breast milk container in the refrigerator for
up to 48 hours (not in the door) or in the freezer for
up to 3 months. Infant formula should be made up
fresh for each feed.

After each cycle the unit should be allowed to cool
for at least 3 minutes before opening and removing
parts. If after a Mode 1 cycle is run the unit must
be allowed to cool for a minimum of 10 minutes prior
to running another sterilisation cycle.

To remove sterilised items after a cycle

To load the Philips AVENT ISIS Manual
Breast Pump

Before each use, wash items to be sterilised in mild soapy
water, and rinse.
1.

Disassemble the ISIS Breast Pump and click the pump
body into the slot in the upper basket and arrange
the other breast pump components as shown.

Place remaining components of the pump in the
lower basket.

Up to six 125ml or 260ml bottles

(not including

screw rings, teats or dome caps)

can be sterilised

with the pump.

Follow sterilising instructions on page 4.

Contents

a) Lid
b) 2 x Upper basket
c) Bottle rack
d) Lower basket (same as b)
e) Central stem
f) Steriliser body
g) Measuring Cup
h) De-scaler (citric acid)
i) Tongs
j) Lead and plug

NB: Upper and lower baskets are identical

Warning: Your Philips AVENT items
may discolour over time if they are
washed in the dishwasher with dirty
items covered with remnants of
strong sauces, such as tomato sauce.

90ml

2(iv)

2(iii)

2(i)

2(ii)

BEEP

Mode 1:

90ml

Mode 2:

200ml

BEEP