2 - 1
2 - 1
System , Region Code , etc. Setting Produre
1)System Reset
a) Press “SETUP“ button on R/C,TV will show setup menu.
b) Select the menu using the and on R/C.
c) Go preference page to do system reset.
2)Region Code Change
a) In open mode, press”9” “9“ “9“ “9“ “9“on R/C,then input desired
number to change region code :
1 USA
2 EU
3 AP
4 Australia ,NZ , Latam
5 Russia , INDIA
6 CHINA
3)Version Control Change
a) In open mode, press “1“ “5“ “9“ on R/C.
b) Press “ok” button to confi rm.
c) TV will show message as below:
8) Upgrading new software
a) Copy “software fi les” into CD-R or USB.
b) Insert CD-R or put USB into USB jack.
c) Press “DISC“ or “USB“ button on R/C.
d) VFD will show:
“LOADING CONTENTS“
pop messange “upgrading“
“Writing” about 1 minute
“done “
e) TV will show:
Current model
HTS6120/55
Release:XXXX.XX.XX Version: XX.XX.XX
region
:X
Servo:XX.XX.XX.XX
8032:XX.XX.XX.XX RISC: XX.XX.XX.XX
If current model does not match you set, use down arrow
key on the remote to change
OK
4)Password Change
a) Press “SETUP“ button on R/C,TV will show setup menu.
b) Select the menu using the V and B on R/C.
c) Go preference page select “password“ to change.
* 136900 is default password supplied.
5)Check on the Software Version
a) Open the CD Door.
b) Press “INFO“ button on R/C.
c) TV will show the version on screen.
CAUTION!
This information is confi dential and may not be
distributed.Only a qualifi ed service person should
reprogram the Region Code.
Upgrade fi le detected
upgrade?
Press OK to start
f) Press “PLAY“, TV will show:
UPGRADING HTS6120
DO NOT POWER DOWN
POWER BOX MCU
PANEL MCU
DVD FLASH
6)Trade model
a) Press “Open/Close “ button on R/C.
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA
OFF“.
7) Produce to Change Tuner Grid
(only applicable for certain regions)
In some countries, the frequency step between adjacent channels
in the FM band is 50kHz (100kHz in some areas).
a) Press “source” to select “FM”.
g) After the system will switch off automatically.
b) In “FM” playback mode, press & hold “play/pause” button until
Grid 9” or “Grid 10” appears.
Note: repeating the same action will toggle back to it previous
tuning grid setting.
* “Grid 10” is default for/98 version.
Содержание HTS6120/55
