RESUME / HOLD
RESUME - continuing from where you have stopped
You can store the last position played. When restarting, playback
will continue from where you have stopped (RESUME).
Use the OFF-RESUME-HOLD slider on the set for this function.
1
Switch the slider to
RESUME
during playback to
activate RESUME.
2
Press
9
whenever you want to stop playback.
3
Press
2;
whenever you want to resume playback
➜
Playback continues from where you have stopped.
•To deactivate RESUME, switch the slider to
OFF
.
Helpful Hints:
– For MP3-CD, as it contains large amount of digital compressed information,
resume function will work only before the set is completely shut off.
HOLD- locking all buttons
You can lock the buttons of the set. When a key is pressed, no action will be
executed. With HOLD activated, you can avoid accidental activation of other
functions.
• Switch the OFF-RESUME-HOLD slider to HOLD
to activate HOLD
➜
HOLd
is displayed briefly.
➜
All buttons are locked and no action will be
executed when you press any button on the set.
If the set is switched off,
HOLd
appears when
2;
is pressed.
• To deactivate
HOLD
, switch the slider to
OFF
➜
All the buttons are unlocked.
ESP, POWER SAVE MODE
With a conventional portable CD player, you might have experienced that music
stopped (e.g. when you were jogging). The
E
lectronic
S
kip
P
rotection prevents
playback interruption caused by light vibrations and shocks. Continuous playback
is ensured. However, ESP does not prevent playback interruptions during vigorous
running.
It also does not protect the unit against any damage caused by
dropping!
The power save mode helps to extend battery service
life for longer playback.
• Press
ESP
once or twice during playback.
➜
ESP
appears when shock protection is activated
• To deactivate the shock protection and enter the
power save mode, press
ESP
again.
➜
ESP
disappears.
100
SEC
MAGIC ESP!
Average playing times when ESP skip protection activated :
Seconds
track type
100
MP3 (128kbps)
45
Audio CD
Helpful Hints:
– For a MP3 CD, ESP is by default always activated.
TROUBLESHOOTING
WARNING:
Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not empty, that they are inserted correctly,
that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
The indication
nO diSC
or
nO AF
is displayed/CD cannot be read
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens have steamed up, wait a few minutes until the lens clear up.
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication
HOLd
is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few sec-
onds.
Music files do not play
• Check that the file names of MP3 files end with .mp3.
TROUBLESHOOTING
Some directories missing on MP3 CDs
• Check that the total number of files and albums on your MP3 CDs
does not exceed 350.
• Only albums with MP3 files are shown.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• Shuffle or program is active. Switch off whichever is on.
Music skips or popping sounds when you play a MP3 track
• Play the music file in your computer. If the problem remains,
encode the audio track again and make a new CD.
No sound or bad sound quality
• Playback on pause. Press
2;
.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check the player's position and connections.
Also keep away from active mobile phones.
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in unsafe oper-
ation.