HOLD
• To deactivate HOLD, switch the slider to
OFF
.
➜
All the buttons are unlocked.
Helpful Hint:
–
If you deactivate HOLD by switching the slider on the set to RESUME, you will
be activating the RESUME function.
ACOUSTIC FEEDBACK (BEEP)
Acoustic feedback is a beep signal that is heard when buttons on the set or
remote control are pressed. Also, when the set or remote control is in pause
mode or the battery power is low, it beeps at intervals.
1
Keep
DBB
pressed for more than 2 seconds to switch the beep either off or
on.
➜
: Beep is switched off.
➜
: Beep is switched on.
Helpful Hint:
–
Beep is on as the default setting
.
RESUME
( main set only, audio CD only)
RESUME - continuing from where you have stopped
You can store the last position played. When restarting, playback will continue
from where you have stopped (RESUME). Use the
OFF-RESUME-HOLD
slider on
the set for this function.
1
Switch the slider to
RESUME
during playback to acti-
vate RESUME.
2
Press
9
whenever you want to stop playback.
3
Press
2;
whenever you want to resume playback (or
on the remote control, press and hold
2;
briefly).
➜
Playback continues from where you have stopped.
• To deactivate RESUME, switch the slider to
OFF
.
HOLD
HOLD - locking all buttons
This player offers a double lock function to prevent buttons from being acciden-
tally pressed and activated. You can choose to lock all buttons on either your set,
remote control or even both! Simply adjust the respective
HOLD
slider to on or
off position as desired. For example:
•
Switch the
OFF•RESUME•HOLD
slider to
HOLD
to
activate HOLD
(or on the remote control, switch the
OFF•HOLD
slid-
er to
HOLD
).
➜
All buttons are locked.
HOLD
is shown when you
press any button on the set / remote control respec-
tively. If the set is locked and switched off,
HOLD
will
be shown only when you press
2;
.
Canada
English
This digital apparatus does not exceed
the Class B limits for radio noise emis-
sions from digital apparatus as set out in
the Radio Interference Regulations of the
Canadian Department of
Communications.
Français
Cet appareil numérique n'émet pas de
bruits radioélectriques dépassant les li-
mites applicables aux appareils
numériques de Classe B prescrites dans
le Règlement sur le Brouillage
Radioélectrique édicté par le Ministère
des Communications du Canada.
TROUBLESHOOTING
WARNING:
Under no circumstances should you try to repair the unit yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
The indication
is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.
• Make sure the CD is not encoded with
Copyright protection technologies
,
as some do not conform to the Compact Disc standard.
The indication
is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication
is displayed
• CD contains non-audio files. Insert a suitable disc or press
SEARCH
∞
/
§
once or more to skip to an audio track, instead of the data file.
The indication
is on and/or there is no reaction to controls
• If
HOLD
is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
•
SHUFFLE
or
PROG
is active. Switch off whichever is on.
No sound or bad sound quality.
• pause might be active. Press
2;
.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.