Please read this user manual carefully before using
this product.
Kind reminder:
Host (x1)
Magnetic Stand(x1)
Sub-unit (x1)
USB cable(x1)
Power Adaptor(x1) User Manual(x1)
Screw (x6)
Packing List
1
User Manual
Appearance overview
1
：
Indoor host
Function
button
Indicator ring
Touch panel
MIC
Speaker
Connector
Charging
interface
Reset
2
Installation
1
：
Confirm installation position
3
Outside door
Inside door
Outside door
6
：
Host Installation
2
1
5
：
Fix sub-unit interface
7
：
Remove the host
2
1
4
：
Magnetic Stand Installation
2
3
1
2
1
2
：
Sub-unit pre-install instruction
3
：
Fix sub-unit
2
：
Outdoor sub-unit
Human detection
sensor(Do not block it )
Camera
(Do not block it)
Doorbell
Microphone
Connecting
cable
Sub-unit
interface
Speaker
1
2
User Manual
To register your product(s) and get support from below site:
www.philips.com/support
Easy
Key
Smart Door Viewer
DV001
Thank you for purchasing Philips-branded products. For your
safety, please read this user manual carefully before using the
product. Any personal injury, property or other loss caused by not
following the user manual or precautions, no liability will be
assumed by Philips.
This user manual is used as a guide. The photos, pictures, or
illustrations provided in the manual are for explanation purposes,
which may differ from the specific product, please refer to the
actual product. Due to product version upgrade or other needs,
Philips may update this manual timely without advanced
informing. If you need the latest version of the manual, please
download it from the Philips website (www.philips.com/support).
The copyright of any part from this manual, including text,
pictures or illustrations, belongs to Philips. Without written
permission, no corporation or individual may extract, copy,
translate, or modify all or part of this manual in any way. Unless
otherwise agreed, Philips does not make any express or implied
representations and guarantees.
If there is no hole on the door, please drill one with a
diameter of 15 ~ 30mm at the height of 145cm from the
ground.
If there is a hole on the door and installed with a peephole,
please remove the peephole and install the smart door
viewer. The hole diameter range should be 15~50mm.
Please choose the proper screw as per the door thickness
for sub-unit installation.
Short size screw is applicable for a door thickness of
35mm-60mm.
Medium size screw is applicable for a door thickness of
60mm-85mm.
Long size screw is applicable for a door thickness of
85mm-110mm.
Sort out the connecting cable, then tighten the screw
into the sub-unit for 5mm, and tear the foam label
protective sheet on the rear side of the sub-unit.
Adjust the direction of the sub-unit from outside and
make sure the doorbell button is at the bottom. Then
pass the screw and connecting cable through the hole. (If
your door is too thick, use a paper tube to pass the cable
through the door, then remove the paper tube ). Press
hard on the sub-unit to make sure it perfectly adheres to
the door, then remove the lens protective film.
1
2
Pass the connecting cable of the sub-unit through the
square hole on the magnetic stand from the inside door
( Do not twist or squeeze the connecting cable.).
Attention: Move down
the magnetic stand so
that the screws can be
matched with the
marked position, and
then fasten the screws.
Attention: Insert the
sub-unit interface into
the groove on the
magnetic stand as shown
in the picture.
Hang the magnetic stand on the screws of the sub-unit and
fasten the screws until the magnetic stand can be fixed firmly
on the door.
Align the sub-unit interface with the groove on the magnetic
stand, and make sure they are stick to each other firmly.
Gently pull out the connecting cable from the inside
door, and then peel off the protection film on the back
of the sub-unit interface.
Attention: Align the host
device to the magnetic
stand from the top to
bottom.
Inside door
Tilt the host by 10 degrees and hang it on the steel sheet
from top to bottom. The bottom magnet will automatically
suck with the host. After installation, gently pull the upper
part of the host to check if it is correctly installed.
Outside door
foam label
Inside door
Please hold the bottom of the host with both hands and
tilt it upwards by 10 degrees, and then move it against the
steel sheet to remove the host.
Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license. This product
has been manufactured by and is sold under the responsibility of
Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen
Conex Intelligent Technology Co., Ltd. is the warrantor concerning
this product.
Version: 1.0
