manualshive.com logo in svg

Philips EasyAir SNS210 MC, Руководство по интеграции в конструкцию

Поделиться
Скачать
Philips EasyAir SNS210 MC Скачать руководство пользователя страница 19

1

9

Design-in Guide - EasyAir SNS210

 MC

August

 202

1

FAQ 

Can you use a wall dimmer with EasyAir SNS210 MC?

SNS210 MC can be used with a wireless wall dimmer,
e.g., Zigbee green power switch. For list of supported
switches, please visit our website

How does EasyAir SNS210 MC compare to Philips ActiLume?

Occupancy sensing and daylight harvesting are similar.
Form factors are also similar, with the face of the sensor
outside the luminaire having the same size. The portion of
EasyAir SNS210 MC within the luminaire is slightly deeper
and longer to accommodate added functionality.  
EasyAir SNS210 MC includes granular dimming together 
with energy reporting and works with Philips Xitanium SR 
LED drivers to eliminate the cost and complexity of a 
separate power pack.

Is EasyAir SNS210 MC a DALI sensor?

EasyAir SNS210 MC works with Philips Xitanium SR
LED drivers, which have inbuilt power supply. It
cannot be used with DALI drivers and therefore,
EasyAir SNS210 MC is not a DALI sensor.

Can I use EasyAir SNS210 MC outside a luminaire?

An accessory option called CMP/w is available to
enable ceiling mounting. Wiring to the driver must be
kept less than 2m.

Can I use one sensor with multiple luminaires?

Yes, and the ceiling mount option is likely utilized in this
use case (called 1:N operation as opposed to 1:1). It usually
means turning off the SR power supplies in all but one of
the SR drivers. See EasyAir SNS210 MC with multiple SR
drivers 1:N application section.

Содержание EasyAir SNS210 MC
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды