Philips BDL4635E Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 52

background image

User Manual BDL4635E

2

REGULATORY INFORMATION

CE DECLARATION OF CONFORMITY

MMD declares under our responsibility that the product is in conformity with the following standards
• EN60950-1:2001+A11:2004 (Safety requirement of Information Technology Equipment)
• EN55022:2006 + A1:2007 (Radio Disturbance requirement of Information Technology Equipment)
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)
• EN61000-3-2:2006 (Limits for Harmonic Current Emission)
• EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on
ISO9000 level.

WARNING

This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required
to take adequate measures.

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING
EQUIPMENT REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

«
...
3
4
5
6
7
...
»

Содержание BDL4635E





















































Отзывы:

Нет отзывов

Похожие инструкции для BDL4635E

Бренд: Barco Страницы: 48

Бренд: Barco Страницы: 66

Бренд: Barco Страницы: 82

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 78

Бренд: Barco Страницы: 8

Coronis 5MP Mammo

Бренд: Barco Страницы: 88

Color Coronis 2MP

Бренд: Barco Страницы: 2

Color Coronis 2MP

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 40

Бренд: Barco Страницы: 52

Бренд: SACAGAWEA DESIGNS Страницы: 6

Бренд: Eversan Страницы: 12

Бренд: Sceptre Страницы: 32

eiQ-43CVSUWD120FSH

Бренд: ElectrIQ Страницы: 21

SmartGLCD 240x128

Бренд: mikroElektronika Страницы: 37

Бренд: OSEE Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды