CD Synchro Start recording
1
Select
CD/MP3
function.
2
Insert a CD and if desired, programme track num-
bers.
3
Open the cassette door.
4
Insert a suitable tape into the cassette deck and
close the door.
5
Press
RECORD
0
to start recording.
™
Playing of the CD/program starts automatically
from the beginning. You don’t need to start the
CD player separately.
™
Display: shows
briefly.
6
To pause recording, press
PAUSE
;
.
Press
PAUSE
;
again to resume recording.
7
To stop recording, press
STOP/OPEN
9/
.
Recording from the Radio
1
Tune to the desired radio station (see Tuning to
radio stations).
2
Follow steps 3-7, under CD Synchro Start recording.
Maintenance & Safety
(See
8
,
9
)
CD player and CD handling
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can
cause condensation on the lens of your CD player.
Playing a CD is then not possible. Do not attempt to
clean the lens but leave the set in a warm environ-
ment until the moisture evaporates.
• Always close the CD door to avoid dust on the lens.
• To clean the CD, wipe in a straight line from the
centre towards the edge using a soft, lint-free cloth.
Do not use cleaning agents as they may damage the
disc.
• Never write on a CD or attach any stickers to it.
Safety Information
•
Place the set on a hard, flat and stable surface so
that the system does not tilt.
•
Do not expose the set, batteries, CDs to humidity,
rain, sand or excessive heat caused by heating
equipment or direct sunlight.
•
The apparatus shall not be exposed to
dripping or splashing.
•
Adequate ventilation with a minimum gap of 15
cm between the ventilation holes and surrounding
surfaces is necessary to prevent heat build-up.
•
The ventilation should not be impeded by covering
the ventilation openings with items, such as news-
papers, table-cloths, curtains, etc..
•
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
•
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
•
The mechanical parts of the set contain
self-lubricating bearings and must not be oiled or
lubricated.
•
To clean the set, use a dry cloth. Do not use any
cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Tape deck maintenance
To ensure quality recording and playback of the tape
deck, clean parts
A
,
B
and
C
as shown, once a
month. Use a cotton bud slightly moistened with alco-
hol or a special head cleaning fluid to clean the deck.
1
Open the cassette door.
2
Press
PLAY
1
and clean the roller
C
.
3
Press
PAUSE
;
and clean the heads
A
, and the
capstan
B
.
4
After cleaning, press
STOP/OPEN
9/
.
Remote control does not function properly
– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Increase the distance
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic aerial
indication
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared
– CD-R/CD-RW is blank/ not finalized
• Use a finalized CD-R(W)
– CD-ROM disc inserted/
CD contains non-audio files
• Use CD Audio discs/MP3-CD only
Note:
Make sure the CD is not encoded with Copyright
protection technologies, as some do not conform
to the Compact Disc standard.
The disc skips tracks
–
Disc damaged or dirty
•
Replace or clean disc
–
SHUF
or
PROG
is active
•
Switch off
SHUF
/
PROG
Note:
For a disc with CD Audio tracks and MP3 files,
the MP3 files may be unplayable, depending on
the encoding software.
Sound skips during MP3 playback
– MP3 file made at compression level exceeding
320kbps
• Use a lower compression level to record CD tracks
into MP3 format
–
Disc damaged or dirty
• Replace or clean disc
Poor cassette sound quality
– Dust and dirt on the heads, etc.
• Clean deck parts, see Maintenance
– Use of incompatible cassette types
(METAL or CHROME)
• Only use NORMAL (IEC
I
) for recording
Recording does not work
– Cassette tab(s) may be broken
• Apply adhesive tape over the missing tab space
WARNING
Do not open the set as there is a risk of electric shock! Under no circumstances should you try to
repair the set yourself, as this will invalidate the guarantee.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
CASSETTE RECORDER
MAINTENANCE & SAFETY
TROUBLESHOOTING