English
Controls/Power Supply
Power Supply
General Operation/Tuner
Using AC power
WARNING: Always check you have
completely switched off the set, before
you change or disconnect power supply.
1
Check if the power voltage,
as shown on
the type plate located on the
bottom of the set,
corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2
Connect the power cord to the
AC MAINS~
inlet and the wall socket.The
set is now connected and ready for use.
3
To switch the set off completely, withdraw the
power cord from the wall socket.
4
Install the unit near the AC outlet and where
the AC power plug can be easily reached.
•
Disconnect the power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Helpful hints:
–
To avoid unnecessary energy consumption,
always adjust the
Source selector
to
OFF
after using the set.
General operation
Switching on and off and selecting the
function
1
To select your sound source, adjust the
Source selector
to:
CD
,
FM
or
MW.
2
To switch off the set, adjust the
Source selector
to
OFF
position.
Adjusting volume
Adjust the sound with the
VOLUME
control.
Radio reception
1
Adjust the
Source selector
to
FM
or
MW
to select your desiredwaveband.
2
Turn
TUNING
to tune to a station.
Helpful hints:
To improve radio reception
•
For
FM
, extend, incline and turn the
telescopic antenna for best reception. Reduce
its length if the signal is too strong.
•
For
MW
, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
Supplied Accessories
– AC power cord
Top/front panels
(See
1
)
1
Source selector
:
CD
,
FM
,
MW or OFF
– selects CD or radio (FM/MW) source of
sound
– power off switch
2
2;
– starts or pauses CD playback
§ ∞
– selects the next/previous track
– fast searches forwards/backwards
(press and hold the button)
PROG
– programs tracks and reviews the
program
9
– stops CD playback;
– erases a CD program
3
Display
– shows the CD functions
4
REPEAT
– repeats a track/
CD program/entire CD.
5
SHUFFLE
– plays all tracks in random order
6
OPEN•CLOSE
– opens/ closes the CD
door
7
TUNING
– tunes to radio stations
8
VOLUME
– adjusts volume level
Back/bottom panels (
See
1
)
9
Telescopic antenna
– improves FM
reception
0
Battery door
– open to insert 6 x 1.5V
R-14
/
UM-2
/
C-cells
!
p
–
3.5 mm stereo headphone socket
Helpful hints:
The speakers will be muted
when headphones are connected to the set.
@
AC MAINS~
– inlet for power cord
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in unsafe
operation.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1
Open the battery door and insert 6 batteries,
type
R-14
,
UM-2
or
C-cells
, (preferably
alkaline) with the correct polarity as indicated
by the "
+
" and "
–
" symbols inside the com-
partment (See
1
).
2
Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set
is now ready to operate.
• Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst
:
• Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
• When inserting new batteries, do not try to mix
old batteries with the new ones.
• Remove the batteries if the set is not to be used
for a long time.
Batteries contain chemical substances, so
they should be disposed of properly.
