Accented Letters and Symbols
Accented characters and symbols are not directly
available on the Remote Control Keyboard.
To type such a character, you can open the onscreen
keyboard.
Qwerty, Azerty and Cyrillic keyboard
The standard layout of the Remote Control Keyboard
is Qwerty.
Azerty keyboard
Depending on your region, the Remote Control
Keyboard can be set to Azerty. The Azerty characters
are shown at the top right of the relevant keys.
To set the keyboard layout to Azerty…
1 -
Press
, select
All Settings
and press
OK
.
2 -
Select
Region and Language
and
press
(right) to enter the menu.
3 -
Select
Remote Control Keyboard
and
press
OK
.
4 -
Select
AZERTY
or
QWERTY
and press
OK
.
5 -
Press
(left) repeatedly if necessary, to close
the menu.
Cyrillic keyboard
Depending on your region, the Remote Control
Keyboard can be switched to Cyrillic characters.
The Cyrillic characters are shown at the top right of
the keyboard keys.
To write Cyrillic characters…
1 -
Press
on the remote control.
2 -
Press
again to switch back to Qwerty.
6.4
Pairing the Remote Control
This remote control uses radio frequency (RF) to send
its commands to the TV. Contrary to remote controls
using infrared signals, you don't have to point at the
TV with RF. For the remote control to communicate
with the TV, both TV and remote control should be
paired (linked) with each other. Once paired, you
cannot use the remote control to control another TV.
Pairing
When you started the initial TV installation, the TV
invited you to press the
OK
key, and by doing so,
the pairing was done. If the TV does not react on any
remote control key press, pairing was unsuccessful.
Pair again
If the pairing with the remote control was lost, you
can pair the TV with the remote control again.
To start pairing...
1 -
On the back of the TV, standing in front of the TV
at the right, press the joystick power key
in for 3
seconds. A message will show that the TV is ready to
pair.
2 -
Press the colour keys
(red) and
(blue)
simultaneously for 1 second. A message appears
when the pairing is successful.
6.5
IR Sensor
The remote control of the TV uses BT (bluetooth) to
send its commands to the TV. With BT, you do not
need to point the remote control at the TV.
However, the TV can also receive commands from a
remote control that uses IR (infrared) to send
commands. If you use such a remote control, always
make sure you point the remote control at the
infrared sensor on the front of the TV.
6.6
Batteries
If the TV does not react on a key press on the remote
control, the batteries might be empty.
To replace the batteries, open the battery
compartment on the keyboard side of the remote
control.
1 -
Slide the battery door in the direction shown by
the arrow.
2 -
Replace the old batteries with 2
type
AAA-R03-1.5V
batteries. Make sure the + and
the - ends of the batteries line up correctly.
3 -
Reposition the battery door and slide it back until
it clicks.
Remove the batteries if you are not using the remote
control for a long time.
Safely dispose of your old batteries according to the
end of use directions.
For more information, in
Help
, press the colour
key
Keywords
and look up
End of use
.
6.7
Cleaning
Your remote control is treated with a scratch-resistant
coating.
To clean the remote control, use a soft damp cloth.
Never use substances such as alcohol, chemicals or
household cleaners on the remote control.
31
Содержание 40PFT6550
Страница 6: ...up Bluetooth or Wireless Speakers 6 ...
Страница 142: ...Powered by TCPDF www tcpdf org 142 ...