Philips 29PT5445/85 Скачать руководство пользователя страница 9

Страница: 9 / 56

Service Modes, Error Codes, and Fault Finding

EN 9

L03.1U AA

Service Modes, Error Codes, and Fault Finding

Index of this chapter:

5.1 Test Points
5.2 Service Modes
5.3 Problems and Solving Tips
5.4 Service Tools
5.5 The Blinking LED Procedure
5.6 Protections
5.7 Repair Tips

5.1

Test Points

This chassis is equipped with test points in the service printing.
In the schematics test points are identified with a rectangle box
around Fxxx or Ixxx. On the PCB, test points are specifically
mentioned in the service manual as “half moons” with a dot in
the center.

Table 5-1 Test Point Overview

Perform measurements under the following conditions:
•

Service Default Alignment Mode.

•

Video: color bar signal.

•

Audio: 3 kHz left, 1 kHz right.

5.2

Service Modes

Service Default Alignment Mode (SDAM) offers several
features for the service technician.
.
There is also the option of using ComPair, a hardware interface
between a computer (see requirements) and the TV chassis. It
offers the ability of structured trouble shooting, error code
reading and software version readout for all chassis.
Requirements: To run ComPair on a computer (laptop or
desktop) requires, as a minimum, a 486 processor, Windows
3.1 and a CD-ROM drive. A Pentium Processor and Windows
95/98 are however preferred (see also paragraph 5.4).

Table 5-2 SW Cluster

5.2.1

Service Default Alignment Mode (SDAM)

Purpose

•

To change option settings.

•

To create a predefined setting to get the same
measurement results as given in this manual.

•

To display / clear the error code buffer.

•

To override SW protections.

•

To perform alignments.

•

To start the blinking LED procedure.

Specifications

•

Tuning frequency: 61.25 MHz (channel 3) for NTSC-sets
(Nafta).

•

Color system: NTSC-M.

•

All picture settings at 50 % (brightness, color contrast,
hue).

•

Bass, treble and balance at 50 %; volume at 25 %.

•

All service-unfriendly modes (if present) are disabled, like:
–

(Sleep) timer,

–

Child/parental lock,

–

Blue mute,

–

Hotel/hospitality mode

–

Auto switch-off (when no “IDENT” video signal is
received for 15 minutes),

–

Skip / blank of non-favorite presets / channels,

–

Auto store of personal presets,

–

Auto user menu time-out.

•

Operation hours counter.

•

Software version.

•

Option settings.

•

Error buffer reading and erasing.

•

Software alignments.

How to enter SDAM

Use one of the following methods:
•

Use a standard customer RC-transmitter and key in the
code 062596 directly followed by the “M” (menu) button or

•

Short jumper wires 9257 and pin 4 of 7200 on the mono
carrier (see Fig. 8-1) and apply AC power. Then press the
power button (remove the short after start-up).

•

Caution: Entering SDAM by shorten wires 9257 and pin 4
of 7200 will override the +8V-protection. Do this only for a
short period. When doing this, the service-technician must
know exactly what he is doing, as it could lead to damaging
the set.

•

Or via ComPair.

After entering SDAM, the following screen is visible, with S at
the upper right side for recognition.

Figure 5-1 SDAM Menu

•

LLLL.

This is the operation hours counter. It counts the

normal operation hours, not the standby hours.

•

AAABCD-X.Y.

This is the software identification of the

main micro controller: