• Check if the the external device or source is
properly connected.
• Check if the reception is poor.
• Check if the picture is set to a minimal value.
Select
Picture style
and select a style and press
OK
.
(Home) > Settings > All
settings > Picture > Picture style
• To check if the TV is broken, try to play a video clip.
Press
Settings
>
Help
>
Check the TV
.
If the video clip stays black, call Philips. Wait until the
clip ends and select
Contact info
in the Help menu.
Call the telephone number for your country.
Sound but no picture
• Change to other video sources and then change
back to current source.
• Select
Picture style
and select a style and
press
OK
.
(Home)
>
Settings
>
All
settings
>
Picture
>
Picture style
• Restore picture style, select back to
Picture style
,
then press
Restore style
.
• Reset all TV settings, go
to
(Home) > Settings > All settings >
General
settings
>
Reinstall TV
.
• Check the connections of the source/input devices.
Poor reception
If the TV picture is distorted or variable in quality, the
input signal might be poor. A weak digital signal is
seen as a picture that is breaking up in square blocks
and freezes occasionally. Much sooner than a bad
analogue signal, a bad digital signal will fall away.
• Check if the antenna cable is properly connected.
• Large loudspeakers, unearthed audio devices, neon
lights, high buildings and other large objects can
influence reception quality when you are using an
antenna. Try to improve the reception by changing
the antenna direction or moving devices away from
the TV. Bad weather might deteriorate the reception.
• Check if all connections, to and from your devices,
are properly connected.
• If reception on only one channel is poor, fine-tune
this channel with
Analogue: manual installation
. (Only
for analogue channels)
(Home) > Settings > Install
Channels > Antenna/cable
installlation >
Analogue: manual installation
• Check if the incoming digital signal is sufficiently
strong. While watching a digital channel,
press
OPTIONS
and select
Status
and
press
OK
. Check the
Signal strenght
and
Signal
quality
.
Poor picture from a device
• Make sure that the device is connected properly.
Make sure that the device's output video setting is the
highest possible resolution if applicable.
• Restore picture style or change to another picture
style.
Picture settings change after a while
Make sure that
Location
is set to
Home
. You can
change and save settings in this mode.
(Home) > Settings > All settings >
General
settings
>
Location
A banner appears
If an on screen promotion banner appears
occasionally or the
Picture style
automatically
switches back to
Vivid
at startup, the TV is in
Shop
location. Set the TV to
Home
location for use at
home.
(Home) > Settings > All settings >
General
settings
>
Location
Picture does not fit the screen / Wrong or unstable
picture size / Picture position is incorrect
• If the picture size - its aspect ratio - does not fit the
screen, with black bars on the top and bottom or left
and right side of the screen, press
Picture
Format
>
Fill screen
.
• If the picture size changes all the
time, press
Picture Format
>
Fit to screen
.
• If the position of the picture is incorrect on the
screen, try to check the signal resolution and output
type of the connected device, press
Picture
Format
>
Original
.
Computer picture is not stable
Make sure that your PC uses the supported resolution
and refresh rate.
18.7
Sound
No sound or poor sound quality
• Check if the sound settings of the TV are OK, press
the
volume or
mute key.
• If you use a digital receiver (set-top box), check if
the volume on this receiver is not set to zero or mute.
• Check if the TV - the audio signal - is properly
connected with the Home Theatre System, if you use
such a system for the TV sound. Check if you
connected the HDMI cable to an
HDMI1
ARC
connection on the Home Theatre System.
• Make sure that the TV audio output is connected to
the audio input on the Home Theatre System.
Sound should be heard from the HTS (Home Theatre
System) speakers.
Sound with loud noise
If you watch a video from a plugged in USB flash drive
or connected computer, the sound from your Home
Theatre System might be distorted. This noise is heard
when the audio or video file has DTS sound but the
Home Theatre System has no DTS sound processing.
You can fix this by setting the
Digital out format
of
the TV to
Stereo
.
Press
(Home) > Settings > All
settings > Sound > Advanced >
Digital out format
52
Содержание 240PW9EB/69
Страница 65: ...Powered by TCPDF www tcpdf org 65 ...
