Philips 19LT010L/35 Скачать руководство пользователя страница 14

Страница: 14 / 67

Use the MENU UP/DOWN keys to highlight the TUNER sub menu.

Press the MENU LEFT/RIGHT keys to enter the TUNER sub menu.

Use the MENU UP/DOWN keys to select AGC.

Use the MENU LEFT/RIGHT keys to adjust the AGC value (default value is 27)
until the voltage at pin 1 of the tuner lies between 3.8V and 2.3V.

10. Press the MENU button to return to the top level SDAM menu.

11. To ensure the AGC change takes effect:

•

Turn the television set OFF by using the POWER button on the remote
control transmitter or the local keyboard.

•

Disconnect the television set from AC power for at least ten seconds.

•

Reconnect the television set to AC power.

•

Turn the television set ON by using the POWER button on the remote
control transmitter or the local keyboard.

SL (Slicing Level)

This adjustment sets the sync slicing level for non-standard signals.
SL should be turned ON to help correct picture instability in premium decoded cable
channels.
OFF: slicing level dependent on noise detector
ON: fixed slicing level of 70%

To adjust SL:

Enter SDAM:

•

Press the following key sequence on the remote control transmitter:
0-6-2-5-9-6-MENU

•

Do not allow the display to time out between entries while keying the
sequence.

Use the MENU UP/DOWN keys to highlight the TUNER sub menu.

Press the MENU LEFT/RIGHT keys to enter the TUNER sub menu.

Use the MENU UP/DOWN keys to select SL.

Use the MENU LEFT/RIGHT keys to toggle SL "Off" and "On"

Press the MENU button to return to the top level SDAM menu.

To ensure the SL setting is saved:

Содержание 19LT010L/35




































































Результаты поиска

Содержание 19LT010L/35

Отзывы:

Похожие инструкции для 19LT010L/35

Бренды по названию

Популярные бренды

Philips 19LT010L/35, Техническая сервисная информация

Результаты поиска

Содержание 19LT010L/35

Отзывы:

Похожие инструкции для 19LT010L/35

Бренды по названию

Популярные бренды