manualshive.com logo in svg

philippi TBM-HANSE, Инструкция по эксплуатации, Страница: 2 / 16

Поделиться
Скачать
philippi TBM-HANSE Скачать руководство пользователя страница 2

k

T A N K   &   B A T T E R Y   M O N I T O R   T B M   -   H A N S E

Page 2 

V1.1 - May 2010

FUNCTIONS WITHOUT BATTERY MANAGEMENT

The tank & battery monitor TBM shows the voltages of your batteries (service- and starter battery, if existing

also the bow battery) and the levels of your tanks (3 or 4).

The TBM shows the voltages of the service- and the starter battery.

without bow battery:

with bow battery:

If an alarm is activated by low voltage you can acknowledge it by pressing an arbitrarily push button.

By pressing the push button under the tank symbol the display changes to the tank monitor.
Depending on the type of your yacht there are 2 fresh water and 1 or 2 diesel tanks:

Water ports.  Water stb.   Diesel

Water ports.  Water stb.  Diesel ports. Diesel Stb. 

The tank level is shown in percentage only.

By pressing the right push button again the display changes to the battery monitor.

Otherwise the displays changes automatically back to the battery monitor after 15s..

The other part of this manual is only interesting if the option battery management with an active shunt is built in.

Содержание TBM-HANSE

















Отзывы:

Нет отзывов