PHICOMM FD-221 Скачать руководство пользователя

Страница: 7 / 61

ADSL2/2+ Modem Router

www.phicomm.com

Chapter 2: Hardware Installation

Chapter 2: Hardware Installation

Front Panel

The front panel of the ADSL2/2+ Modem Router includes one power indicator and three
function indicators, as explained in table below:

LED

Status

Description

Power

Power is on

Off

Power is off

LAN

There is a successful connection on the Ethernet port

Off

There is no connection on the Ethernet port or the connection is abnormal

Blinking

Data is being transferred over the Ethernet port

DSL

The Modem Router is synchronized

Blinking

The Modem Router is synchronizing

Internet

Green

A successful PPP connection has been built

Off

The DSL port is linked down or the Modem Router works in Bridge mode

Red

The PPP connection failed to be established

Содержание FD-221





























































Результаты поиска

Содержание FD-221

Отзывы:

Похожие инструкции для FD-221

Бренды по названию

Популярные бренды

PHICOMM FD-221, Руководство пользователя

Результаты поиска

Содержание FD-221

Отзывы:

Похожие инструкции для FD-221

Бренды по названию

Популярные бренды