background image

Install instructions for CI round flush mount models, Page 2

1.

 Using the supplied cutout template, 

carefully mark the area to be cut out. Using

a drywall knife or saw, cut a hole in the

drywall and prepare the speaker wires for 

connection to the speaker terminals.

2.

 Remove the grille from the mounting

flange by pressing it from behind. Insert the

mounting flange into the hole. Loosen the

flange clamping screws one turn (counter

clockwise) to release the clamp. Next,

tighten all four flange clamp screws evenly

to secure the flange to the wall. It is best to

tighten each screw with the same amount of

force (torque). 

CAUTION: Do not over-tighten.

Flange Installation:

3.

 Connect the speaker wires to the

spring-loaded input terminals on the rear of

the speaker, making sure no loose strands

are exposed. If connecting the CI-6.2s VIII QM,

see wiring options below.

Speaker Installation:

+

_

Red/positive         Black/negative

5.

 Using some familiar source material,

listen to the tweeter’s balance with the level

control in each of its three positions to find

your favorite.

6.

 Carefully replace the grille by pressing it

into the gap between the flange and the

baffle. Enjoy your new Phase Technology

speakers!

Grille

4.

 Carefully place the speaker in the flange.

While exerting upward pressure, rotate the

speaker until it fits snugly and the speaker

surface is even with or slightly recessed 

into the surface of the flange. Rotate the

speaker counter-clockwise (left) to secure

it in place. This will engage the Quick Mount

clamps on the back of the flange. Finish by

tightening the four clamp screws on the

speaker. 

CAUTION: Do not over-tighten. 

Quick Mount Clamp

Wiring options for the CI-6.2s 

Right Channel

Right  Channel

Stereo Point Source 

FIG.2

 – 

8 ohms: 

Use this configuration to combine left 
and right channels for full fidelity sound 
from a single loud-speaker stereo source. 
Set jumper plugs in the stereo position. 
Connect 

right

 and 

left 

signal wires to the 

spring-loaded terminals on the rear of 
the speaker. 

Jumper Plugs

stereo position

Jumper Plugs

stereo position

Mono/S tereo 

FIG.3 – 

4 ohms: Use 

this configuration to drive one channel 
(

left or right

) of a stereo pair with a 4 

ohm speaker load. Set jumper plugs in 
the mono position. Connect the right or 
left signal wire to the left set of posts 
on the rear of the speaker. Acoustic 
output of the speaker is increased by 
3 dB in the configuration.

Bi-pole/Di -pole 

FIG.4 

– 

4 ohms: Use this 

configuration for home theater surround 
applications. For 

bi-pole

 

mode

, connect 

as in the 

Mono/ Stereo

 

instructions 

(FIG.3)

one speaker to each surround channel. 
For 

di-pole mode

, connect speaker 

inputs the same as 

Mono/ Stereo

 

instructions 

(FIG.3)

, but reverse the 

+

 and 

 

connections of the marked tweeter wires 
to put one of the tweeters out of phase.

Left Channel

Left Channel

Stereo 

FIG. 1 – 

8 ohms: Use this 

configuration to drive one channel 
(

left or  right

) of a stereo pair. Set 

jumper plugs in the stereo position. 
Connect the right or left signal wire to 
the right set of terminals on the rear of 
the speaker.

Jumper Plugs

mono position (Bi-pole/di-pole)

3

.

G

I

F

2

.

G

I

F

1

.

G

I

F

FIG.4

6400 Youngerman Circle  /  Jacksonville, FL 32244  /  (888)PHASE TK  /  www.phasetech.com

NOTE: Special instructions for non-QM 

Flanges

If you are installing a CI round speaker with 

the QM clamps in a CI-FGR (non-QM flange) 

remove the QM clamp feet by unscrewing 

them from the speaker baffle. Insert the 

speaker baffle into the flange and reuse the 

screws from the clamp feet to attach the 

speaker to the flange.

Отзывы: