Phase Linear Phase Linear CD1211, Руководство пользователя

Страница: 8 / 20

CD1211
8
Balance
Press the AUDIO CONTROL button (4) four
times until “BAL” appears in the display. Within
five seconds, turn the
AUDIO CONTROL (3)
clockwise (or counter clockwise) to adjust
Balance between the right and left speakers
from “BAL 10R” (full right) to “BAL 10L” (full
left). “BAL L=R” represents an equal balance
level between the right and left speakers. The
balance position is shown on the display for five
seconds or until another function is activated.
Fader
Press the AUDIO CONTROL (4) five times until
“FAD” appears in the display. Within five
seconds, turn the
AUDIO CONTROL (3)
clockwise or counter clockwise to adjust
balance between the front and rear speakers
from “FAD 10R” (full rear) to “FAD 10F” (full
front). “FAD F=R” represents an equal balance
level between the front and rear speakers. The
fader position is shown on the display for five
seconds or until another function is activated.
X-BASS (BAND)
Press and hold the BAND button (5) for two
seconds to activate the X-BASS feature. When
listening to music at low volume levels, this
feature will boost the bass and treble ranges to
compensate for the characteristics of human
hearing. When activated, “X-BAS” appears on
the display. Press
BAND again for two seconds
to deactivate this feature.
Audio Mute (MUTE)
Press (6) to mute the audio volume. “MUTE”
flashes on the display. Restore volume to the
previous setting by pressing the mute button
again, adjusting the
AUDIO CONTROL , or by
pressing any other button on the unit.
Beep Tone
The beep tone feature allows the selection of
an audible beep tone to be heard each time a
button is pressed on the face of the radio. To
access the Beep Tone menu,
press and hold
the AUDIO CONTROL (4). Turn the AUDIO
CONTROL to select from the following Beep
Tone options:
•
BEEP ALL: Beep is heard any time a
button is pressed (function activated).
• BEEP 2ND: Beep is heard only when a
secondary function is activated (press and
hold).
• BEEP OFF: Beep is not heard.
Equalizer Selector (EQ)
The equalizer function applies preset sound
effects to the unit’s audio output signal. Press
EQ (20) to activate one of the following
operating modes: FLAT, CLASSICS, POP M,
ROCK M or DSP OFF. When the equalizer
function is activated, the most recently selected
bass/treble levels are ignored. If the bass and/
or treble levels are adjusted while the equalizer
function is active, the equalizer function will
revert to FLAT. When the equalizer function is
not active, the unit will return to the most
recently selected bass and treble levels.
Liquid Crystal Display (LCD)
The liquid crystal display (LCD) panel (8)
displays the frequency, time and activated
functions of the unit, including an audio level
indicator, which appears as a bar graph
depicting the audio signal. In addition, the
display contains a receive signal indicator that
depicts the relative strength of the incoming
broadcast frequency.
NOTE: After being subjected to cold
temperatures, LCD panels may take longer
to respond and visibility of the numbers on
the LCD may decrease slightly. The LCD
display will return to normal when the
temperature increases to a normal range.
VOL
VOL
BAS
TRB
BAL
FAD
P
U
S H
S E
E
L
C
T
B
B
S
L
E
T
A
A
AD F R
P
U
S H
S E
E
L
C
T
B
B
S
L
E
T
A
A
AD F R
P
U S
H
S E
E
L
C
T
B
B
S
L
E T
A
A
AD
F R
P U
S
H S
E
E L
C
T
B
B S
L
E T
A
A
AD F
R