PFT SWING L FU Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 60

PFT SWING L FU Series Скачать руководство пользователя страница 49

PFT

Conveying Pump SWING L

Overview – Operation

– Spare Parts Lists

Maintenance

14/09/2021

49

Fig. 71: Remove connection cable

DANGER!
Danger of death due to electric current!

Contact with live components can lead to death or

serious injury. Live electrical components can move

uncontrollably and cause serious injury.
Therefore:



Before starting work, switch off the electrical power

supply and secure it against being switched back

on again.



Interrupt the power supply by removing the

connection cable.

DANGER!
Danger of death due to unauthorised restarting!

When working on the SWING L system, there is a
danger of unauthorised switching on of the electrical
supply. This puts those in the danger area at
extreme risk.



Before starting work, switch off all electrical power
supplies and secure them against being switched
back on again.



Interrupt the power supply by removing
the connection cable.



For further instructions, refer to the booklet item
number 00172709 General safety instructions for
mixing pumps.

NOTE!
The control box may only be opened by an
electrician or a person trained in electrical
engineering.

Observe the following notes on environmental protection when
carrying out maintenance works:



Remove the discharged, exhausted or surplus grease at all
greasing points that are lubricated manually and dispose of in
accordance with the local applicable regulations.



Collect replaced oil in suitable containers and dispose of in
accordance with the local applicable regulations.

«
...
47
48
49
50
51
...
»

Содержание SWING L FU Series





























































Отзывы:

Нет отзывов