PFS Dry-Vac 200 Скачать руководство пользователя страница 12

Страница: 12 / 13

VACUUM SYSTEM CHECK LIST

CHECK

LIST

CHECKS

Open cooling water supply valve. Is it flow properly?

Close Vacuum suction line

Open discharge line

Check lubricant color and level. Is it acceptable?

Check Belt tension (for V-belt type only), coupling alignment

Before

Operation

Run Vacuum pump for few minutes before open the suction line

Check vacuum level in full vacuum. Is it normal?

Check electrical connections (voltage & amperage) in full vacuum.

Is it normal?

Any abnormal noise?

Check operation temperature. Is it normal?

During

Operation

Check lubricant color and level. Is it acceptable?

Run Vacuum pump for few minutes after closing suction line.

If foreign material is introduced inside of vacuum pump, clean it with

cleaning agent.

Drain cooling water from vacuum pump if the pump is stopped for long

time

Make sure that suction & discharge line is closed

Stopping

Make sure power supply is closed

Содержание Dry-Vac 200














Результаты поиска

Содержание Dry-Vac 200

Отзывы:

Похожие инструкции для Dry-Vac 200

Бренды по названию

Популярные бренды

PFS Dry-Vac 200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Dry-Vac 200

Отзывы:

Похожие инструкции для Dry-Vac 200

Бренды по названию

Популярные бренды