background image

petsafe.com

+1 (800) 732-2677

25

24

Wire Break Location Test

Please inspect these areas for signs of damage.

Wire breaks are commonly found:

•  At the wire exit point of the house
•  Where the wire enters the ground from the house, usually caused by 

string trimmers

•  Where the wires cross sidewalks or driveways, usually caused by edging 

and string trimmers

•  Around landscaping and flower beds, usually caused by digging, or 

working up the soil

•  In aerated lawns
•  At wire splices where gel-filled capsules have not been installed
•  At wire splices without reinforcement knots (

22A

)

If you still cannot find the break in the boundary wire, there are 

2 options for locating it:
Option 1:

 It is recommended to contact the Customer Care Center to 

purchase a Wire Break Locator (RFA-590) (

22B

). The Wire Break Locator 

detects full breaks, not partial breaks.

Option 2:

 Follow the procedure below:

1.  Unplug the fence transmitter.
2.  Connect both ends of your boundary wire to one loop terminal on 

the transmitter.

3.  Measure and cut a test wire which is half the length of your total boundary 

wire footage.

4.  Connect one end of test wire to the other loop terminal on the transmitter.
5.  Locate the halfway point of your boundary and cut the boundary wire.
6.  Splice the other end of the test wire to either side of your boundary wire 

where you cut it in half.

7.  Plug in the fence transmitter, set to Traditional mode (B), and check the 

transmitter for the wire break alarm. If the wire break alarm is on, you can 
assume that the break is in this half of the boundary wire.

8.  If the wire break alarm did not come on, you may assume there is a break in 

the other portion of the boundary wire. However, there is a small chance of 
having more than one break in your system. Be sure to check both halves of 
your entire loop.

9.  Replace the damaged boundary wire with new boundary wire. 
10. Reconnect the boundary wire to the transmitter.
11. Check the loop indicator light. If the loop indicator light is on, test the system 

with the receiver collar.

22A

22B

Receiver Collar Status Indicators 

The receiver collar light and the alarm tones are used to determine the operational mode, the battery status and the correction level. Refer to the 
receiver collar status table below to understand the status lights and tones for the receiver collar. During normal operation, the receiver collar light will 
flash every 4 seconds to indicate the battery status as shown in the table below. If your receiver collar has not been moved for at least 20 seconds, the 
battery status light will function, but the receiver collar will enter sleep mode to conserve battery life. To wake up the receiver collar simply pick it up and 
flip it over or shake it.

Receiver Collar Status Table

Light Status

Alarm Tone

Condition

While Plugged into the Receiver Charger

Solid red

No tone

Charge in progress

Solid green

No tone

Charge complete

No light

No Tone

Charge failure—contact Customer Care Center

ReadyTest

®

 Startup

 

(After removing the receiver collar from the charger or after first turning it on)

Off for 1 second

No tone

Unit is starting the ReadyTest

®

 startup feature

Continuous red, green, or red+green together 

(5 seconds)

No tone

Battery charge status

Flashing red from 1 to 6 times

No tone

Receiver collar is reporting the 

static correction level from 1 to 6

Continuous red

20 seconds

 ReadyTest

®

 failure; 

Unit is not operational—contact Customer Care Center

PerfectFit Test

Flashing red+green together 

(every 1 second)

No tone 

Unit is in PerfectFit mode for 90 seconds 

after the ReadyTest

®

 startup is completed

Flashing green 

(every 1 second)

5 consecutive double tones 

for a confirmed fit

PerfectFit mode indicates that the collar is making true 

contact with the pet’s skin

Static Correction Level

Flashing red from 1 to 6 times

No tone

Receiver collar is reporting the 

static correction level from 1 to 6

Receiver Activation Status

Fast pulsating green

Warning tone

Warning tone

Fast pulsating red

Duration of the correction

Static correction is being delivered 

(up to 15 seconds)

Continuous green 

(10 seconds)

No tone

 Over Correction Protection feature; 

Collar is locked for 10 seconds

Slow blinking green 

(every 4 seconds)

No tone

Collar battery charge 100%–60% 

Slow blinking red+green together 

(every 4 seconds)

No tone

Collar battery charge 60%–20%

Slow blinking red 

(every 4 seconds)

No tone

Collar battery charge 20% or less; 

Charge immediately

Содержание YardMax Cordless In-Ground Fence


















Отзывы: