background image

 

and reflects this on the TX port of the other SFP by turning off the 
transmitter. When the signal (Link) gets restored and Signal 
Detector becomes active the affected transmitter gets re-enabled.  
 
Standard Mode: In Standard Mode the media converter will 
monitor the fiber link in the same manner. If Signal Detect goes 
down the media converter will output a 25MHz signal on the TX 
port of the other SFP. 

Fiber Fault Alert (Switch 2) 

Switch Position 

Mode 

Up (default) 

Disabled 

Down 

Enabled 

 
Enabled: If the media converter detects a loss of fiber signal on its 
fiber receiver, it will disable its fiber transmitter on the same SFP. 
This, in effect, notifies the fiber link partner that an error condition 
exists on the fiber connection. 
  
Disabled: The Protocol Transparent Media Converter will not 
monitor for Fiber Fault. 

Rate Select (Switch 3) 

Switch Position  Mode 

Up (default) 

High Speed 

Down 

Low Speed 

 
High Speed – When a multi-rated SFP is inserted, it is enabled for 
its higher speed of operation. 
 
Slow Speed – When a multi-rated SFP is inserted, it is enabled 
for its slower speed of operation. 
 

Содержание S-4GPT-DSFP









Отзывы: