background image

Perle S- 10G Media Converter Installation Guide

    

 

 

16 

Compliance Information  

FCC 

This product has been found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated 
in a commercial environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions in this Guide, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful 
interference, in which case the user will be required to correct the interference at 
his/her own expense. 

EN 55022 Class A  

WARNING

 

This is a Class A product. In a domestic environment this product may 

cause radio interference in which case the user may be required to take adequate 
measures. 

EN 55024 Class A  

Contacting Technical Support 

Contact information for the Perle Technical Assistance Center 
(PTAC) can be found at the link below. A Technical Support Query 
may be made via this web page. 

www.perle.com/support_services/support_request.shtml 

Warranty / Registration 

Perle’s standard Lifetime Warranty provides customers with return 
to factory repairs for Perle products that fail under the conditions of 
the warranty coverage. Details can be found at: 

http://www.perle.com/support_services/warranty.shtml 

 

Copyright 

© 2012 Perle Systems Limited 

All rights reserved. No part of this document may be reproduced or used in any form 
without written permission from Perle Systems Limited. 

Содержание S-10G-STS

















Отзывы: