Perle IDS-305 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 26

Perle IDS-305 Скачать руководство пользователя страница 9

7

IDS-305 Hardware Installation Guide

Ports

10/100/1000Base-T Ports

These ports provide the standard gigabit Ethernet interface. They provide speeds of 10/100 or
1000 Mb/s through twisted pair (UTP) cables of up to 100 meters (328ft) in length.

RJ-45 Console Port

This is a console management port which will provide access to the switch management function using
our industry standard CLI command set. This port has an RJ-45 connector. See RJ-45-Console Port Pin

-

outs for pinouts.

Power Connector

The power input connector has provisions for dual inputs. Two independent power sources can be used
to power the switch. If one power input fails, the other power input will power the switch.

Alarm Relay Connector

The Alarm Relay can be energized by the software or hardware under certain conditions. It can then be
used to trigger an external alarm circuit such as a light or sounding device. This connector provides a
Normally Closed (NC) dry contact on the connector block.

«
...
7
8
9
10
11
...
»

Содержание IDS-305



























Отзывы:

Нет отзывов